544268
20
Zoom out
Zoom in
Previous page
1/314
Next page
20 | English
1 609 929 V13 | (18.11.10) Bosch Power Tools
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the to-
tal working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical Data” is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 10.11.2010
Assembly
f Before any work on the machine itself, pull
the mains plug.
Operation without Drill Stand
f Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal
injury.
Screw the auxiliary handle 16 into the thread 9
on the drill head. If required, turn the drill head
to one of the four possible positions to achieve
a low-fatigue and safe working stance (see
“Mounting the Drill Head”).
Operation with Drill Stand
f The safety and operating instructions for
the drill stand being used are to be strictly
observed!
For safety reasons, the machine should general-
ly be clamped in the S 500 A diamond drill
stand.
For mounting the power tool into the drill stand,
please read and observe the operating instruc-
tions of the drill stand.
Mounting/Replacing the Drill Head
f Operation with drill stand: Before any work
on the machine itself, for longer work
breaks, as well as when not using, secure
the power tool against unintentional motion
by engaging the feed lock. For this, read and
observe the operating instructions of the drill
stand.
Drill Head Selection
The GDB 1600 WE can be operated with the
flushing head 6 and with the suction head 19.
For operation with wet-drilling core bits, mount
the flushing head; for operation with core bits
(dry drilling), mount the suction head.
For safety reasons, the GDB 1600 DE can only
be operated with the suction head 19 for dry
drilling core bits. This is ensured by means of a
special encoding of power tool and drill head.
Mounting the Drill Head
Loosen the clamping screw 15 on the flushing
head 6 or on the suction head 19 respectively
until the securing pin 14 is pulled completely
back into the housing.
Mount the flushing head or the suction head re-
spectively to the stop on the drill head holder
20. The latching cogs 21 of the drill head holder
must engage in the latching grooves 7 on the
drill head. Four 90° offset positions are possible
for this. Mount the drill head in the position at
which all contol elements can be reached well.
Firmly tighten the clamping screw 15 again.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-116-003.book Page 20 Thursday, November 18, 2010 11:49 AM
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GDB 1600 WE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GDB 1600 WE in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 16,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info