Manual Bosch GCR 350 Professional (page 12 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591912

Zoom out

Zoom in

1/132

12 | English

1 609 92A 0VZ | (30.10.14) Bosch Power Tools

Fold the drill onto the drill fixture  and reinsert the eccentric

bolt 3. Tighten the eccentric bolt 3 using the star handle 4.

Slide the star handle 4 right or left onto the feed pinion 15 in

order to drill.

 Check the tight seating of the drill in the drill fixture.

To remove the drill from the drill stand, complete the steps in

reverse order.

Spacer Plate for Drilling Diameters of 300–350 mm

(see figure C)

The spacer plate 18 (accessory) has to be additionally insert-

ed in order to drill holes of 300 mm to maximum 350 mm

diameter.

To do so, attach the machine adapter 14 to the spacer plate

18 so that the feather keys 13 of the machine adapter engage

into the corresponding slots on the spacer plate.

Then attach the spacer plate 18 including machine adapter

14 to the drill so that the feather keys 20 of the spacer plate

engage into the corresponding recesses of the drill. Insert the

four screws 19 of the spacer plate and tighten them using a

hex key (size 6 mm).

Then mount the drill on the drill stand as described above.

Fastening the Drill Stand

Note: Fasten the drill stand free from play to prevent jamming

of the core bit and the tearing out of segments.

Depending on the type and nature of the structural material,

fasten the drill stand where the bore hole is intended using an

anchor, with vacuum or with the quick-clamping column.

Positioning the Drill Stand before Fastening

Mark the centre of the bore hole you want to drill on the surface.

Mark the outer dimensions of the core bit you want to drill with,

using the centre of the bore hole as the centre of the bit.

Fasten the drill stand (with drill inserted) using anchors, vac-

uum or quick-clamping column so that the mounted core bit is

aligned with the marked dimensions.

Fastening with Anchor (see figure D)

For fastening of the drill stand to brickwork or concrete with

anchor (accessory), drill a separate anchor hole.

The following dimensions apply for the anchor hole:

Insert a concrete hammer-drive anchor or a brickwork anchor

21. Screw the quick-clamping spindle 22 into the anchor.

Position the drill stand, attach a washer, and then screw to-

gether with the wing nut 23. After levelling (see “Levelling”),

tighten the wing nut using an open-end spanner, size 27 mm.

Fastening with Vacuum (Accessory)

To fasten the drill stand with vacuum, you require a conven-

tional vacuum pump and a Bosch vacuum set (accessory).

The vacuum pump must meet the following minimum require-

ments:

The surface must be smooth and flat in order to fasten with

vacuum. Use on plaster or brickwork is not permitted.

Once the vacuum connection has been established, apply the

levelling screws 7 lightly to the surface so that the drill stand

is in a rigid position and the sealing ring relaxes slightly. Oth-

erwise the drill stand will sit very softly on the sealing ring.

Read and observe the operating instructions of the vacuum

pump and Bosch vacuum set in order to connect them.

 The safety and operating instructions for the vacuum

pump and vacuum set are to be strictly observed!

Fastening with a Quick-clamping Column (see figure E)

You can fasten the drill stand between the floor and ceiling us-

ing a Bosch quick-clamping column (accessory). The clamp-

ing range is 1.7 m to 3 m.

Place one end of the quick-clamping column on the bottom

plate of the drill stand. The contact surface on the ceiling for

the other end of the quick-clamping column must be suffi-

ciently stable and resistant to slipping.

For fastening the quick-clamping column, read and observe

its operating instructions.

Levelling (does not apply for fastening with vacuum)

Turn the levelling screws 7 in or out individually until the spirit

level 17 (when mounting vertically) is precisely aligned.

Now, firmly fasten the drill stand with anchor attachment or

with the quick-clamping column.

Operation

 Disconnect the plug from the power source before

making any adjustments or changing accessories.

Starting drills accidentally is the cause of some accidents.

 After each adjustment on the drill stand, firmly retight-

en all screws.

Drilling-angle Adjustment

Loosen the cap nut 6 using the star handle 4.

Set the drill stand to the required drilling angle using the drill-

ing-angle scale 2. Observe the arrow next to the cap nut 6 for

the exact setting.

Tighten the cap nut 6 hand-tight using the star handle 4.

 The drill stand must not be inserted until the cap nut 6

of the angle adjustment has been retightened.

Water Extraction

You require a water collection ring and a wet/dry vacuum

cleaner (both accessories) to collect the water escaping from

the bore hole during wet drilling.

Clearance from anchor hole–centre of the intended bore

hole

optimal 285 mm

possible 275–375 mm

Diameter Depth

Brickwork 20 mm 85 mm

Concrete 16 mm 50 mm

Volume flow: 6 m

Vacuum at least: 80 % (–800 mbar)

OBJ_BUCH-2255-001.book Page 12 Thursday, October 30, 2014 1:59 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GCR 350 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GCR 350 Professional Manual

Product: