592623

Bosch GCO 2000 Professional Manual

19
Zoom out
Zoom in
Previous page
1/227
Next page
English | 19
Bosch Power Tools 1 609 92A 0Y1 | (17.9.14)
– Place the workpiece against the angle stop 7.
– Slide the clamping spindle 8 against the workpiece and
firmly clamp the workpiece with the spindle handle 10.
Loosening the Workpiece
– Loosen the spindle handle 10.
– Tilt up the quick release 9 and pull the clamping spindle 8
away from the workpiece.
Starting Operation
Observe the mains voltage! The voltage of the power
source must correspond with the data on the type plate of
the machine.
Check the cutting disc before using. The cutting disc
must be properly mounted and must rotate freely. Car-
ry out a 30 second (min.) test run with no load. Do not
use damaged, out-of-centre or vibrating cutting discs.
Damaged cutting discs can burst and cause injuries.
Dusts from materials such lead-containing coatings, minerals
and metal can be harmful to one’s health. Contact with or in-
haling the dusts can trigger allergic reactions to the operator
or bystanders and/or lead to respiratory infections.
Certain metal dusts are considered hazardous, especially in
conjunction with alloys such as zinc, aluminium or chromium.
Materials containing asbestos may only be worked by special-
ists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
The blade can be blocked by dust, chips or workpiece frag-
ments in the slot of the base plate 12.
– Switch the machine off and pull the mains plug from the
socket outlet.
– Wait until the cutting disc has come to a complete stop.
– Tilt the machine toward the rear, so that small workpiece
fragments can fall out of the opening intended for this pur-
pose.
If required, use a suitable tool to remove all workpiece frag-
ments.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Position of the Operator (see figure F)
Do not stand in a line with the cutting disc in front of the
machine. Always stand aside of the cutting disc. This
measure provides for better protection of your body
against possible splinters in case of cutting disc breakage.
Switching On and Off (see figure G)
To save energy, only switch the power tool on when using it.
–To start the machine, firstly press the lock-off button 1.
Then press the On/Off switch 2 and keep it pressed.
Note: For safety reasons, the On/Off switch 2 cannot be
locked; it must remain pressed during the entire operation.
–To switch off the machine, release the On/Off switch 2.
Soft starting
The electronic soft starting feature limits the torque upon
switching on and increases the working life of the motor.
Working Advice
General Cutting Instructions
Do not touch the cutting disc after working before it
has cooled. The cutting disc becomes very hot while work-
ing.
Make sure that the spark guard 20 is properly mount-
ed. Sparking occurs when cutting metal.
Protect the cutting disc against impact, shock and grease. Do
not subject the cutting disc to lateral pressure.
Do not strain the power tool so heavily that it comes to a
standstill.
Excessive feed considerably reduces the performance capa-
bility of the machine and shortens the service life of the cut-
ting disc.
Use only cutting discs that are suitable for the material to be
worked.
Permissible Workpiece Dimensions
Maximum workpiece sizes:
Minimum workpiece sizes
(= all workpieces that can be clamped via the clamping spin-
dle 8): Length 80mm
Cutting depth, max. (0°/0°): 125 mm
Cutting Metal
– Set the desired mitre angle.
– Firmly clamp the workpiece as appropriate for its dimen-
sions.
– Switch on the machine.
– Slowly guide the tool arm downward with the handle 3.
– Cut the workpiece applying uniform feed.
– Switch the machine off and wait until the cutting disc
comes to a complete stop.
– Guide the tool arm slowly upward.
Mitre/Bevel Angle
Workpiece Form 0° 45°
125 Ø 100 Ø
110 x 110 82 x 82
180 x 85 90 x 75
130 x 130 75 x 75
OBJ_BUCH-1063-004.book Page 19 Wednesday, September 17, 2014 9:34 AM
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GCO 2000 Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GCO 2000 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info