Manual Bosch GCO 2000 Professional (page 15 of 227) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

592623

Zoom out

Zoom in

1/227

English | 15

Bosch Power Tools 1 609 92A 0Y1 | (17.9.14)

 Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a ro-

tating part of the power tool may result in personal injury.

 Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

 Dress properly. Do not wear loose clothing or jewel-

lery. Keep your hair, clothing and gloves away from

moving parts. Loose clothes, jewellery or long hair can be

caught in moving parts.

 If devices are provided for the connection of dust ex-

traction and collection facilities, ensure these are con-

nected and properly used. Use of dust collection can re-

duce dust-related hazards.

Power tool use and care

 Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

 Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

 Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

 Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

 Maintain power tools. Check for misalignment or bind-

ing of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power

tools.

 Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

 Use the power tool, accessories and tool bits etc. in ac-

cordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

Service

 Have your power tool serviced by a qualified repair per-

son using only identical replacement parts. This will en-

sure that the safety of the power tool is maintained.

Safety Warnings for Cut-off Grinder

 Never stand on the power tool. Serious injuries could oc-

cur when the power tool tips over or when accidentally

coming into contact with the cutting disc.

 Always use the blade guard. A blade guard protects the

user against broken off parts of the cutting disc and against

accidental touching of the cutting disc.

 Make sure that the guard operates properly and that it

can move freely. Never lock the guard in place when

opened.

 Use the power tool only for dry cutting. Water penetrat-

ing into a power tool increases the risk of an electric shock.

 Keep the mains cable away from rotating application

tools. The mains cable can be cut through or get caught.

 Keep handles dry, clean, and free from oil and grease.

Greasy, oily handles are slippery causing loss of control.

 Never remove cutting remainders, metal chips, etc.

from the cutting area while the machine is running. Al-

ways guide the tool arm back to the neutral position first

and then switch the machine off.

 Guide the cutting disc against the workpiece only when

the machine is switched on. Otherwise, there is danger of

kickback, when the cutting disc becomes wedged in the

workpiece.

 Operate the power tool only when the work area to the

workpiece is clear of any adjusting tools, metal chips,

etc. Small pieces of metal or other objects that come in

contact with the rotating cutting disc can strike the opera-

tor with high speed.

 Always firmly clamp the workpiece. Do not cut work-

pieces that are too small to clamp. Otherwise, the clear-

ance of your hand to the rotating cutting disc is too small.

 If the cutting disc becomes jammed, switch the ma-

chine off and wait until the cutting disc comes to a com-

plete stop. Never attempt to remove a still running cut-

ting disc from the cut, otherwise there is danger of

kickback. Determine and correct the cause for the jam-

ming.

 After switching off, do not stop the cutting disc by ap-

plying lateral pressure to it. The cutting disc can become

damaged, break or lead to kickback.

 Do not force the cutting disc into the workpiece and do

not apply too much pressure when using the power

tool. Particularly avoid jamming or wedging the cutting

disc when working corners or sharp edges. When the

cutting disc is damaged due to abuse, cracks can form that

can lead to breakage without prior warning.

 Wear a work apron. Pay attention that other persons

are not put at risk from sparking. Remove flammable

materials in close vicinity. Sparking occurs when cutting

metal.

 Use the cut off grinder only for cutting materials men-

tioned under “Intended Use”. Otherwise, the cut off

grinder can be subject to overload.

 Do not use damaged, out-of-centre or vibrating cutting

discs. Damaged cutting discs cause increased friction,

binding of the cutting disc and kickback.

 Always use cutting discs with correct size and shape

(diamond versus round) of arbor holes. Cutting discs

that do not match the mounting hardware of the cut off

grinder will run eccentrically, causing loss of control.

OBJ_BUCH-1063-004.book Page 15 Wednesday, September 17, 2014 9:34 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GCO 2000 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GCO 2000 Professional Manual

Product: