786479

Bosch GCM 350-254 Manual

37
Zoom out
Zoom in
Previous page
1/475
Next page
English | 37
Preparing for operation
Extending the saw table (see figure F)
The free end of long workpieces must have something
placed underneath it or be supported.
The saw table can be extended left and right using the saw
table extensions (27).
– Loosen the clamping screw (49).
– Pull out the saw table extension (27) to the required
length.
– Retighten the clamping screw (49) to fix the saw table ex-
tension.
Moving the fence (see figureG)
When sawing mitre and/or bevel angles, you have to pull the
left-hand or right-hand adjustable fence(2) outwards de-
pending on the cutting direction, or remove it completely.
If necessary, reinstall the adjustable fence(2) after making
the cut.
Vertical bevel angle range
–2° to +40° Left – Loosen the locking screw(35).
– Pull the adjustable fence(2) all the way out.
–2° to +35° Right
>40° Left – Loosen the locking screw(35).
– Pull the adjustable fence(2) all the way out.
– Lift the adjustable fence upwards and out of the way.
>35° Right
Horizontal bevel angle range
>45° Left – Loosen the locking screw(35).
– Pull the adjustable fence(2) all the way out.
Right
Clamping the workpiece (see figure H)
To ensure maximum safety while working, the workpiece
must always be firmly clamped.
Do not saw workpieces that are too small to clamp firmly.
– Press the workpiece firmly against the fences (1) and (2).
– Insert the supplied screw clamp (38) into one of the cor-
responding holes (29).
– Loosen the wing bolt and adjust the screw clamp to the
workpiece. Tighten the wing bolt again.
– Tighten the threaded rod (50) to fix the workpiece in
place.
Releasing the workpiece
– To loosen the screw clamp, turn the threaded rod (50)
anticlockwise.
Adjusting mitre angles
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Experience and suitable special tools are required for this.
A Bosch after-sales service point will handle this work
quickly and reliably.
Note for adjusting mitre angles >45°:
Before adjusting the mitre angle, pull the saw table
extension(27) and the adjustable fence(2) all the way out.
Setting Standard Mitre Angles (see figure I1)
For quick and precise setting of commonly used mitre
angles, detents (25) are provided on the saw table:
Leftward Rightward
0°
45°; 31.6°; 22.5°; 15° 15°; 22.5°; 31.6°; 45°; 60°
– Loosen the locking knob (21) if it is tightened.
– Pull the lever (22) and rotate the saw table (18) left or
right to the required detent.
– Release the lever again. The lever must be felt to engage
in the detent.
– Retighten the locking knob (21).
Setting Any Mitre Angle (see figure I2)
The mitre angle can be set between 52° (left side) and 60°
(right side).
– Loosen the locking knob (21) if it is tightened.
– Pull the lever (22) and at the same time press the locking
clamp (20) until this clicks into the slot provided for it.
This means the saw table can now move freely.
– Turn the saw table (18) left or right by the locking knob
until the angle indicator (24) shows the required mitre
angle.
– Retighten the locking knob (21).
– To loosen the lever (22) again (for setting standard mitre
angles), pull the lever upwards.
The locking clamp (20) springs back into its original posi-
tion and the lever (22) can click back into the detents
(25).
Adjusting bevel angles
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Experience and suitable special tools are required for this.
A Bosch after-sales service point will handle this work
quickly and reliably.
The bevel angle can be set between 47° (left side) and 47°
(right side).
Bosch Power Tools 1 609 92A 7N9 | (26.04.2022)
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GCM 350-254 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GCM 350-254 in the language / languages: All languages as an attachment in your email.

The manual is 11.42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info