594618

Bosch GCM 12 SDE Professional Manual

38
Zoom out
Zoom in
Previous page
1/402
Next page
38 | English
1 609 92A 0Z5 | (22.12.14) Bosch Power Tools
Adjusting: (see figureU2)
– Loosen the lock nut of the stop screw 63 using a conven-
tional ring spanner or open-end spanner (10 mm).
– Screw the stop screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
–Tighten clamping lever 7 again.
– Then retighten the lock nut of the stop screw 63.
When the angle indicators 43 and 5 are not in line with the 45 °
marks of scale 4 after adjusting, firstly once more check the
0° setting for the bevel angle and the angle indicators. Then
repeat the adjustment of the 45° bevel angle.
Setting the Standard 45° Bevel Angle (Rightward)
– Bring the power tool into the working position.
– Turn the saw table 19 to the 0° detent 26. The lever 23
must be felt to engage in the detent.
– Remove the right-hand adjustable fence 2 (see “Moving
the Fence”, page 34).
– Pull the stop 44 completely forward.
– Turn the right-hand stop 3 until the standard 45° bevel an-
gle engages at the arrow mark.
– Loosen clamping lever 7.
– Swing the tool arm to the right by the handle 12 until the
stop screw 64 rests on the stop 3.
Checking: (see figure V1)
– Set an angle gauge to 135° and place it on the saw table
19
.
The leg of the angle gauge must be flush with the saw blade 48
over the complete length.
Adjusting: (see figureV2)
– Loosen the lock nut of the stop screw 64 using a conven-
tional ring spanner or open-end spanner (10 mm).
– Screw the stop screw in or out until the leg of the angle
gauge is flush with the saw blade over the complete length.
–Tighten clamping lever 7 again.
– Then retighten the lock nut of the stop screw 64.
When the angle indicators 43 and 5 are not in line with the 45 °
marks of scale 4 after adjusting, firstly once more check the
0° setting for the bevel angle and the angle indicators. Then
repeat the adjustment of the 45° bevel angle.
Aligning the Scale for Mitre Angles
– Bring the power tool into the working position.
– Turn the saw table 19 to the 0° detent 26. The lever 23
must be felt to engage in the detent.
Checking: (see figure W1)
– Adjust an angle gauge to 90° and position it between the
fence 1 and the saw blade 48 on the saw table 19.
The leg of the angle gauge must be flush with the saw blade 48
over the complete length.
Adjusting: (see figureW2)
– Loosen all four set screws 65 with the hex key (4 mm) 38
and turn the saw table 19 together with the scale 27 until
the leg of the angle gauge is flush with the saw blade over
the complete length.
– Retighten the screws again.
When the angle indicator 25 is not in line with the 0° mark of
scale 27 after adjusting, loosen screw 66 with a cross-head
screwdriver and align the angle indicator alongside the
0°mark.
Transport (see figure X)
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw 6 if tightened. Pull the tool arm
completely to the front and tighten the locking screw
again.
– Make sure that the depth stop 41 is swung completely
backward and that the adjusting screw 40 fits through the
recess without touching the depth stop when moving the
tool arm.
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Wind up the mains cable and tie it together with Velcro
strap 67.
– Carry the machine by the transport handle 10 or hold it by
the recessed handles 29 on the sides of the saw table.
The power tool should always be carried by two per-
sons in order to avoid back injuries.
When transporting the power tool, use only the trans-
port devices and never use the protective devices.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Cleaning
For safe and proper working, always keep the power tool and
its ventilation slots clean.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean.
Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
Clean the roller 16 regularly.
Measures for Noise Reduction
Measures on behalf of the manufacturer:
–Soft starting
– Delivery of the machine with a saw blade developed partic-
ularly for noise reduction
Measures on behalf of the user:
– Low-vibration assembly on a firm working surface
– Use of saw blades with noise-reducing functions
– Regular cleaning of saw blade and power tool
OBJ_BUCH-2301-002.book Page 38 Monday, December 22, 2014 10:15 AM
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GCM 12 SDE Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GCM 12 SDE Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 28,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info