591831

Bosch GBM 6 RE Professional Manual

8
Zoom out
Zoom in
Previous page
1/34
Next page
8 | English
1 619 P11 530 | (4.2.14) Bosch Power Tools
Assembly
Changing the Tool
Before any work on the machine itself, pull the mains
plug.
Wear protective gloves when changing the tool.
The drill
chuck can become very hot during longer work periods.
Keyless Chuck (see figure A)
Hold the rear sleeve 3 of the keyless chuck 1 tight and turn the
front sleeve 2 in rotation direction , until the tool can be in-
serted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight and firmly
tighten the front sleeve 2 by hand in rotation direction , un-
til the locking action (click) is heard. The drill chuck is locked
automatically.
The locking is released again to remove the tool when the
front sleeve 2 is turned in the opposite direction.
Key Type Drill Chuck (see figure B)
Open the key type drill chuck 10 by turning until the tool can
be inserted. Insert the tool.
Insert the chuck key 9 into the corresponding holes of the key
type drill chuck 10 and clamp the tool uniformly.
Screwdriver Tools (see figure C)
When working with screwdriver bits 11, a universal bit holder
12 should always be used. Use only screwdriver bits that fit
the screw head.
Replacing the Drill Chuck
For machines without spindle lock, the drill chuck must be re-
placed through an authorized after-sales service agent for
Bosch power tools.
The drill chuck must be tightened with a tightening
torque of approx. 31–35 Nm.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Operation
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Reversing the rotational direction (GBM 6 RE)
(see figure D)
The rotational direction switch 8 is used to reverse the rota-
tional direction of the machine. However, this is not possible
with the On/Off switch 7 actuated.
Right Rotation: For drilling and driving in screws, push the
rotational direction switch 8 left to the stop.
Left Rotation: For loosening and unscrewing screws and
nuts, press the rotational direction switch 8 through to the
right stop.
Switching On and Off
To start the machine, press the On/Off switch 7 and keep it
pressed.
To lock the pressed On/Off switch 7, press the lock-on
button 6.
To switch off the machine, release the On/Off switch 7 or
when it is locked with the lock-on button 6, briefly press the
On/Off switch 7 and then release it.
Adjusting the Speed (GBM 6 RE)
The speed of the switched on power tool can be variably ad-
justed, depending on how far the On/Off switch 7 is pressed.
Light pressure on the On/Off switch 7 results in a low rotation-
al speed. Further pressure on the switch results in an increase
in speed.
Max. drilling dia.
– Steel
– Wood
–Aluminium
mm
mm
mm
6.5
15
6
6.5
15
6
6
15
6
Chuck clamping range
mm 0.5 – 6.5 0.5 – 6.5 0.8 – 6
Weight according to EPTA-Procedure 01/2003
kg 1.1 1.1 1.1
Protection class
/II /II /II
Rotary drill GBM 6
Professional
GBM 6 RE
Professional
GBM 6 RE
Professional
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
OBJ_BUCH-837-005.book Page 8 Tuesday, February 4, 2014 12:59 PM
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GBM 6 RE Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBM 6 RE Professional in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info