78818
16
Zoom out
Zoom in
Previous page
1/90
Next page
1 609 929 M58 | (13.9.07) Bosch Power Tools
16 | English
Noise/Vibration Information
Measured values determined according to
EN 60745.
Typically the A-weighted noise levels of the prod-
uct are: Sound pressure level 86 dB(A); Sound
power level 97 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) deter-
mined according to EN 60745:
Drilling into metal: Vibration emission value
a
h
=3.1 m/s
2
, Uncertainty K <1.5 m/s
2
.
The vibration emission level given in this informa-
tion sheet has been measured in accordance
with a standardised test given in EN 60745 and
may be used to compare one tool with another. It
may be used for a preliminary assessment of ex-
posure.
The declared vibration emission level represents
the main applications of the tool. However if the
tool is used for different applications, with differ-
ent accessories or poorly maintained, the vibra-
tion emission may differ. This may significantly
increase the exposure level over the total work-
ing period.
An estimation of the level of exposure to vibra-
tion should also take into account the times
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the
product described under “Technical Data” is in
conformity with the following standards or
standardization documents: EN 60745 according
to the provisions of the directives 2004/108/EC,
98/37/EC (until Dec. 28, 2009), 2006/42/EC
(from Dec. 29, 2009 on).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
01.08.2007, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Assembly
Auxiliary Handle
f Operate your machine only with the auxiliary
handle 5.
Screw the auxiliary handle 5 into the thread 4 on
the gear head.
Changing the Tool (see figure A)
f Before any work on the machine itself, pull
the mains plug.
Drilling tools with a MK3 morse taper can be in-
serted directly into the tool holder 1. For drill bits
with MK2 morse taper, use the reducing sleeve 9.
Pay attention that the morse cone and the morse
taper are free of grease.
The use of drilling tools with cylindrical shank is
possible with the key chuck 11. For this, screw
the tapered arbor 10 onto the key chuck 11 and
insert the tapered arbor with the reducing sleeve
9 into the tool holder 1.
f Do not exert any force when inserting the
morse taper or the tapered arbor. This can
damage the tool holder and the inserted tool.
Place the drift 8 into the opening 2 in such a man-
ner that the rounded-off side faces to the auxilia-
ry handle 5.
If the drift 8 cannot be inserted through the drive
spindle, turn the tool insert a little.
Press the drift 8 toward the auxiliary handle 5
and release the tool insert from out of the tool
holder.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-506-001.book Page 16 Thursday, September 13, 2007 10:31 AM
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GBM 32-4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBM 32-4 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info