Manual Bosch GBM 16-2 RE (page 18 of 107) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

78640

Zoom out

Zoom in

1/107

18 | English

1 609 929 T41 | (12.11.09) Bosch Power Tools

Replacing the Drill Chuck (see figure C)

To dismount the key type drill chuck 1 position

an open-end spanner (size 27 mm) against the

nut on the drive spindle. Firmly hold the key

type drill chuck with one hand and with the oth-

er hand, turn the open-end spanner in anticlock-

wise direction until the drill chuck is released

from the tapered drill spindle.

f Keep the drill spindle taper and the drill

hole of the drill chuck free from grease and

debris.

To mount the key type drill chuck 1 turn the nut

on the drive spindle in clockwise direction to

the stop. Place the key type drill chuck without

force onto the drive spindle until it is tightly

seated. Apply light blows with a rubber hammer

onto the face side of the key type drill chuck 1

to ensure tight seating of the chuck. Pay atten-

tion that the clamping jaws of the key type drill

chuck do not project, in order not to damage

them.

Dust/Chip Extraction

f Dusts from materials such as lead-containing

coatings, some wood types, minerals and

metal can be harmful to one’s health. Touch-

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

tions of the user or bystanders.

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Operation

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Reversing the Rotational Direction

The rotational direction switch 6 is used to re-

verse the rotational direction of the machine.

However, this is not possible with the On/Off

switch 4 actuated.

Right rotation: For drilling and screwdriving,

press the rotational direction switch 6 down-

ward to “R”.

Left rotation: For loosening and unscrewing

screws and nuts, press the rotational direction

switch 6 upward to “L”.

Gear Selection, Mechanical

f Actuate the gear selector 2 only when the

machine is at a standstill.

Two speed ranges can be preselected with the

gear selector 2.

1st gear:

Low speed range; for working with

large drilling diameter.

2nd gear:

Higher speed range; for working

with small drilling diameter.

If the gear selector 2 cannot be fully engaged,

lightly rotate the drive spindle with the drill bit

by twisting the drill chuck.

OBJ_BUCH-21-004.book Page 18 Thursday, November 12, 2009 11:37 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBM 16-2 RE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GBM 16-2 RE Manual

Product: