Manual Bosch GBM 16-2 RE Professional (page 13 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591840

Zoom out

Zoom in

1/72

English | 13

Bosch Power Tools 1 609 929 T41 | (24.10.11)

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with the fol-

lowing standards or standardization documents: EN 60745

according to the provisions of the directives 2011/65/EU,

2004/108/EC, 2006/42/EC.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

05.10.2011

Assembly

f Before any work on the machine itself, pull the mains

plug.

Auxiliary Handle (see figure A)

f Operate your machine only with the auxiliary handle 9.

The auxiliary handle 9 can be set to any position for a secure

and low-fatigue working posture.

Turn the bottom part of the auxiliary handle 9 in counterclock-

wise direction and swivel the auxiliary handle 9 to the desired

position. Then retighten the bottom part of the auxiliary han-

dle 9 by turning in clockwise direction.

Adjusting the Drilling Depth

The required drilling depth X can be set with the depth stop 7.

Loosen the wing bolt for the depth stop adjustment 8 and in-

sert the depth stop rod into the auxiliary handle 9.

Pull out the depth stop until the distance between the tip of

the drill bit and the tip of the depth stop correspond with the

desired drilling depth X.

Changing the Tool (see figure B)

f Wear protective gloves when changing the tool. The drill

chuck can become very hot during longer work periods.

Open the key type drill chuck 1 by turning until the tool can be

inserted. Insert the tool.

Insert the chuck key 5 into the corresponding holes of the key

type drill chuck 1 and clamp the tool uniformly.

Replacing the Drill Chuck (see figure C)

To dismount the key type drill chuck 1 position an open-end

spanner (size 27 mm) against the nut on the drive spindle. Firm-

ly hold the key type drill chuck with one hand and with the other

hand, turn the open-end spanner in anticlockwise direction until

the drill chuck is released from the tapered drill spindle.

f Keep the drill spindle taper and the drill hole of the drill

chuck free from grease and debris.

To mount the key type drill chuck 1 turn the nut on the drive

spindle in clockwise direction to the stop. Place the key type

drill chuck without force onto the drive spindle until it is tightly

seated. Apply light blows with a rubber hammer onto the face

side of the key type drill chuck 1 to ensure tight seating of the

chuck. Pay attention that the clamping jaws of the key type

drill chuck do not project, in order not to damage them.

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Operation

Starting Operation

f Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Reversing the Rotational Direction

The rotational direction switch 6 is used to reverse the rota-

tional direction of the machine. However, this is not possible

with the On/Off switch 4 actuated.

Right rotation: For drilling and screwdriving, press the rota-

tional direction switch 6 downward to “R”.

Left rotation: For loosening and unscrewing screws and

nuts, press the rotational direction switch 6 upward to “L”.

Gear Selection, Mechanical

f Actuate the gear selector 2 only when the machine is at

a standstill.

Two speed ranges can be preselected with the gear selector 2.

1st gear:

Low speed range; for working with large drill-

ing diameter.

2nd gear:

Higher speed range; for working with small

drilling diameter.

If the gear selector 2 cannot be fully engaged, lightly rotate

the drive spindle with the drill bit by twisting the drill chuck.

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Engineering Director

PT/ESI

OBJ_BUCH-21-005.book Page 13 Monday, October 24, 2011 10:57 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBM 16-2 RE Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch GBM 16-2 RE Professional

Bosch GBM 16-2 RE Professional User Manual - Polish - 69 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GBM 16-2 RE Professional Manual

Product: