591837
19
Zoom out
Zoom in
Previous page
1/129
Next page
English | 19
Bosch Power Tools 2 609 932 788 | (20.12.10)
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical Data” is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 2006/42/EC.
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
22.11.2010
Assembly
Auxiliary Handle
(GBM 13-2/GBM 13-2 RE)
(see figure A)
f Operate your machine only with the auxilia-
ry handle 10.
The auxiliary handle 10 can be set to any posi-
tion for a secure and low-fatigue working pos-
ture.
Turn the bottom part of the auxiliary handle 10
in counterclockwise direction and swivel the
auxiliary handle 10 to the desired position. Then
retighten the bottom part of the auxiliary handle
10 by turning in clockwise direction.
Adjusting the Drilling Depth
The required drilling depth X can be set with the
depth stop 11.
Press the button for the depth stop adjustment
9 and insert the depth stop into the auxiliary
handle 10.
The knurled surface of the depth stop 11 must
face downward.
Pull out the depth stop until the distance be-
tween the tip of the drill bit and the tip of the
depth stop correspond with the desired drilling
depth X.
Changing the Tool
f Before any work on the machine itself, pull
the mains plug.
f Wear protective gloves when changing the
tool. The drill chuck can become very hot
during longer work periods.
Keyless Chuck (see figure B)
Hold the rear sleeve 3 of the keyless chuck 1
tight and turn the front sleeve 2 in rotation di-
rection n, until the tool can be inserted. Insert
the tool.
Hold the rear sleeve 3 of the keyless chuck 1
tight and firmly tighten the front sleeve 2 by
hand in rotation direction o, until the locking
action (click) is heard. The drill chuck is locked
automatically.
The locking is released again to remove the tool
when the front sleeve 2 is turned in the opposite
direction.
Key Type Drill Chuck (see figure C)
Open the key type drill chuck 14 by turning until
the tool can be inserted. Insert the tool.
Insert the chuck key 13 into the corresponding
holes of the key type drill chuck 14 and clamp
the tool uniformly.
Screwdriver Tools (see figure D)
When working with screwdriver bits 15, a uni-
versal bit holder 16 should always be used. Use
only screwdriver bits that fit the screw head.
Replacing the Drill Chuck
f Before any work on the machine itself, pull
the mains plug.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
OBJ_BUCH-321-003.book Page 19 Monday, December 20, 2010 8:40 AM
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GBM 13-2 Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBM 13-2 Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info