78753
18
Zoom out
Zoom in
Previous page
1/100
Next page
1 619 929 732 | (9.8.07) Bosch Power Tools
18 | English
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
Setting the Operating Mode
The operating mode of the power tool is selected
with the mode selector switch 3.
Note: Change the operating mode only when the
machine is switched off! Otherwise, the machine
can be damaged.
Turn the mode selector switch 3 to the requested
position.
In the “chiselling” position, the impact rate
preselected with the thumbwheel 5 is automati-
cally increased when switching on; this causes
the power tool to operate with increased capaci-
ty when chiselling.
Switching On/Off in Drilling Mode
To start the machine, press the On/Off switch 4
and keep it depressed.
To switch off the machine, release the On/Off
switch 4.
Switching On/Off in Chiselling Mode
To start the machine, press the On/Off switch 4
at the top (I) until it locks.
To switch off the machine, press the On/Off
switch 4 at the bottom (0) and release it.
For low temperatures, the power tool reaches
the full hammer/impact capacity only after a cer-
tain time.
Setting the Speed/Impact Rate
The electronic control enables stepless speed
and impact preselection in accordance with the
material to be worked.
The constant electronic control keeps the prese-
lected speed and impact rate nearly constant be-
tween no-load and load conditions.
The maximum hammering capacity is achieved
when the thumbwheel 5 is set to position “6”.
For lower speed settings, the hammering capaci-
ty is lower due to technical reasons.
Select the speed with the thumbwheel 5 accord-
ing to the material.
The data in the following table are recommended
values.
Position for hammer drilling
When the drilling tool does not im-
mediately rotate upon switching on,
allow the machine to run slowly un-
til the drilling tool rotates.
Vario-Lock position for adjustment
of the chiselling position
Position for chiselling
Operating
Mode
Hammer Drilling Chiselling
Thumb-
wheel 5
Rated
Speed
(rpm)
Impact
Rate
(bpm)
Impact
Rate
(bpm)
1 145 1350 1375
2 170 1625 1650
3 200 1975 2025
4 225 2175 2225
5 255 2475 2550
6 280 2700 2800
OBJ_BUCH-414-001.book Page 18 Thursday, August 9, 2007 10:45 AM
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GBH 7-46 DE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBH 7-46 DE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info