591885
16
Zoom out
Zoom in
Previous page
1/188
Next page
16 | English
1 619 92A 06G | (2.12.13) Bosch Power Tools
Retighten the wing bolt 20 again. Loosen the clamping
screw 17 on the depth stop of the dust extraction attach-
ment.
Move the depth stop 18 on the telescopic pipe 19 in such
a manner that the clearance X shown in the figure corre-
sponds with the required drilling depth.
–Tighten the clamping screw 17 in this position.
Operation
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Setting the operating mode
The operating mode of the power tool is selected with the
mode selector switch 5.
Note: Change the operating mode only when the machine is
switched off! Otherwise, the machine can be damaged.
Turn the mode selector switch 5 to the requested position.
Reversing the rotational direction
Actuate the rotational direction switch 8 only when the
machine is at a standstill.
The rotational direction switch 8 is used to reverse the rota-
tional direction of the machine.
Right rotation: Turn the rotational direction switch 8 to the
stop in the position .
Left rotation: Turn the rotational direction switch 8 to the
stop in the position .
Set the direction of rotation for hammer drilling, drilling and
chiselling always to right rotation.
Switching On and Off
–To start the machine, press the On/Off switch 7 and keep
it pressed.
–To switch off the machine, release the On/Off switch 7.
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
To save energy, only switch the power tool on when using it.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on power tool can be
variably adjusted, depending on how far the On/Off switch 7
is pressed.
Light pressure on the On/Off switch 7 results in low speed/im-
pact rate. Further pressure on the switch increases the
speed/impact rate.
Safety Clutch
If the tool insert becomes caught or jammed, the drive
to the drill spindle is interrupted. Because of the forces
that occur, always hold the power tool firmly with both
hands and provide for a secure stance.
If the power tool jams, switch the machine off and loos-
en the tool insert. When switching the machine on with
the drilling tool jammed, high reaction torques can oc-
cur.
Changing the Chiselling Position (Vario-Lock)
The chisel can be locked in 13 positions. In this manner, the
optimum working position can be set for each application.
Insert the chisel into the tool holder.
Turn the mode selector switch 5 to the “Vario-Lock” posi-
tion (see “Setting the operating mode”, page 16).
Turn the tool holder to the desired chiselling position.
Turn the mode selector switch 5 to the “chiselling” posi-
tion. The tool holder is now locked.
For chiselling, set the rotation direction to right rotation.
Working Advice
Before any work on the machine itself, pull the mains
plug.
Vibration Damper
The integrated vibration damper reduces occurring vibra-
tions.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
Position for drilling without im-
pact in wood, metal, ceramic and
plastic as well as for screwdriving
Position for hammer drilling in
concrete or stone
When the drilling tool does not
immediately rotate upon switch-
ing on, allow the machine to run
slowly until the drilling tool ro-
tates.
Vario-Lock position for adjust-
ment of the chiselling position
Position for chiselling
OBJ_BUCH-337-007.book Page 16 Monday, December 2, 2013 12:32 PM
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GBH 4-32 DFR Professional at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBH 4-32 DFR Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info