Manual Bosch gbh 36 vf li 2 (page 26 of 333) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

388756

Zoom out

Zoom in

1/333

26 | English

1 619 929 777 | (23.7.07) Bosch Power Tools

Note: If the tool holder was opened to the stop,

then the latching noise possibly may be heard

while closing the tool holder and the tool holder

will not close.

In this case, turn the front sleeve 23 once in the

opposite direction of the arrow. Afterwards, the

tool holder can be closed (tightened) again.

Turn the mode selector switch 10 to the “drill-

ing” position.

Removing Drilling Tools without SDS-plus

(GBH 36 VF-LI) (see figure J)

Firmly hold the retaining ring 24 of the quick

change chuck. Open the tool holder by turning

the front sleeve 23 in the direction of the arrow

until the tool can be removed.

Dust Extraction with the Dust

Extraction Attachment (Accessory)

Mounting the Dust Extraction Attachment

(see figure K)

For dust extraction, the dust extraction attach-

ment (accessory) is required. When drilling, the

dust extraction attachment retracts so that the

attachment head is always close to the surface

at the drill hole.

Press the button for depth stop adjustment 12

and remove the depth stop 17. Press button 12

again and insert the dust extraction attachment

into the auxiliary handle 18 from the front.

Connect an extraction hose (diameter 19 mm,

accessory) to the extraction sleeve 25 of the

dust extraction attachment.

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Adjusting the Drilling Depth on the Dust

Extraction Attachment (see figure L)

The required drilling depth X can also be adjust-

ed when the dust extraction attachment is

mounted.

Insert the SDS-plus drilling tool to the stop into

the SDS-plus tool holder 3. Otherwise, the mov-

ability of the SDS-plus drilling tool can lead to

incorrect adjustment of the drilling depth.

Loosen the wing bolt 29 on the dust extraction

attachment.

Without switching the power tool on, apply it

firmly to the drilling location. The SDS-plus drill-

ing tool must face against the surface.

Position the the guide pipe 30 of the dust ex-

traction attachment in its holding fixture in such

a manner that the head of the dust extraction at-

tachment faces against the surface to be drilled.

Do not slide the guide pipe 30 further over the

telescopic pipe 28 of the dust extraction attach-

ment than required, so that as much as possible

of the scale 28 on the telescopic pipe remains

visible.

Retighten the wing bolt 29 again. Loosen the

clamping screw 26 on the depth stop of the dust

extraction attachment.

Move the depth stop 27 on the telescopic pipe

28 in such a manner that the clearance X shown

in the figure corresponds with the required drill-

ing depth.

Tighten the clamping screw 26 in this position.

Operation

Starting Operation

Inserting the Battery

f Use only original Bosch lithium ion batter-

ies with the voltage listed on the nameplate

of your power tool. Using other batteries can

lead to injuries and pose a fire hazard.

Set the rotational direction switch 7 to the cen-

tre position to protect the power tool against

accidental starting.

Insert the charged battery 16 from the front into

the base of the power tool. Push the battery

completely into the base until the red stripe can

no longer be seen and the battery is securely

locked.

OBJ_BUCH-283-001.book Page 26 Monday, July 23, 2007 12:41 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gbh 36 vf li 2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 18,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch gbh 36 vf li 2 Manual

Product: