Manual Bosch GBH 36 V-LI Plus Professional (page 19 of 273) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591721

Zoom out

Zoom in

1/273

English | 19

Bosch Power Tools 1 609 92A 0JA | (22.6.15)

Removing the Key Type Drill Chuck

– Push the locking sleeve 5 toward the rear and pull out the

key type drill chuck 23.

Removing/Inserting the Quick Change Chuck

(GBH 36 VF-LI Plus)

The SDS-plus quick change chuck 2 can easily be replaced

against the quick change keyless chuck 1 provided.

Removing the Quick Change Chuck (see figure D)

– Pull the lock ring for the quick change chuck 6 toward the

rear, hold it in this position and pull off the SDS-plus quick

change chuck 2 or the quick change keyless chuck 1 to-

ward the front.

– After removing, protect the replacement chuck against

contamination.

Inserting the Quick Change Chuck (see figure E)

 Use only model-specific original equipment and pay at-

tention to the number of identification grooves 26.On-

ly quick-change chucks with two or three identification

grooves are permitted. When an unsuitable quick-change

chuck is used, the application tool could fall out during op-

eration.

– Before inserting, clean the quick change chuck and apply a

light coat of grease to the shank end.

– Grasp the SDS-plus quick change chuck 2 or the quick

change keyless chuck 1 completely with your hand. Slide

the quick change chuck with a turning motion onto the drill

chuck mounting 25 until a distinct latching noise is heard.

– The quick change chuck is automatically locked. Check the

locking effect by pulling the quick change chuck.

Changing the Tool

The dust protection cap 4 largely prevents the entry of drilling

dust into the tool holder during operation. When inserting the

tool, take care that the dust protection cap 4 is not damaged.

 A damaged dust protection cap should be changed im-

mediately. We recommend having this carried out by

an after-sales service.

Changing the Tool (SDS-plus)

Inserting SDS-plus Drilling Tools (see figure F)

The SDS-plus drill chuck allows for simple and convenient

changing of drilling tools without the use of additional tools.

– GBH 36 VF-LI Plus: Insert the SDS-plus quick change

chuck 2.

– Clean and lightly grease the shank end of the tool.

– Insert the tool in a twisting manner into the tool holder until

it latches itself.

– Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus drilling tool can

move freely. This causes a certain radial run-out at no-load,

which has no effect on the accuracy of the drill hole, as the

drill bit centres itself upon drilling.

Removing SDS-plus Drilling Tools (see figure G)

– Push back the locking sleeve 5 and remove the tool.

Changing the Tool (without SDS-plus)

(GBH 36 V-LI Plus)

Inserting (see figure H)

Note: Do not use tools without SDS-plus for hammer drilling

or chiselling! Tools without SDS-plus and their drill chucks are

damaged by hammer drilling or chiselling.

– Insert a key type drill chuck 23 (see “Inserting/Removing

the Key Type Drill Chuck”, page 18).

– Open the key type drill chuck 23 by turning until the tool

can be inserted. Insert the tool.

– Insert the chuck key into the corresponding holes of the

key type drill chuck 23 and clamp the tool uniformly.

– Turn the mode selector switch 13 to the “drilling” position.

Removing (see figure I)

– Turn the sleeve of the key type drill chuck 23 with the drill

chuck key in anticlockwise direction until the drilling tool

can be removed.

Changing the Tool (without SDS-plus)

(GBH 36 VF-LI Plus)

Inserting (see figure J)

Note: Do not use tools without SDS-plus for hammer drilling

or chiselling! Tools without SDS-plus and their drill chucks are

damaged by hammer drilling or chiselling.

– Insert the quick change keyless chuck 1.

– Firmly hold the retaining ring 29 of the quick change

chuck. Open the tool holder by turning the front sleeve 28

until the tool can be inserted. Tightly hold the retaining ring

29 and firmly turn the front sleeve 28 in the direction of the

arrow until a distinct latching noise can be heard.

– Check the tight seating by pulling the tool.

Note: If the tool holder was opened to the stop, then the latch-

ing noise possibly may be heard while closing the tool holder

and the tool holder will not close.

In this case, turn the front sleeve 28 once in the opposite di-

rection of the arrow. Afterwards, the tool holder can be

closed (tightened) again.

– Turn the mode selector switch 13 to the “drilling” position.

Removing (see figure K)

– Firmly hold the retaining ring 29 of the quick change

chuck. Open the tool holder by turning the front sleeve 28

in the direction of the arrow until the tool can be removed.

Dust Extraction with GDE 16 Plus (Accessory)

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

OBJ_BUCH-283-012.book Page 19 Monday, June 22, 2015 10:28 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBH 36 V-LI Plus Professional in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 20,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GBH 36 V-LI Plus Professional Manual

Product: