Manual Bosch GBH 24,0 VFR (page 8 of 11) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

78752

Zoom out

Zoom in

1/11

English - 3

Battery Charging

A battery that is new or has not been used for a

longer period does not develop its full capacity

until after approximately 5 charging/discharging

cycles.

To remove the battery 10, push back the release

button 13 and pull the battery out downwards. Do

not exert any force (see figure ).

Please refer to the enclosed “Battery Charger” in-

structions for the operation of the battery charger

as well as for a description of the charging proc-

ess.

The battery is equipped with an NTC temperature

control which allows charging only within a tem-

perature range of between 0 °C and 45 °C.

A long battery service life is achieved in this man-

ner.

A significantly reduced working period after

charging indicates that the batteries are used and

must be replaced.

■ Observe the notes on environmental protec-

tion.

Battery Charge Display

The battery 10 is fitted with a battery charge dis-

play 9. It indicates the charge of the battery at

any given time during the working process.

By pressing the button 8, the battery charge can

also be checked when the battery has been re-

moved, or when the machine is at a standstill. Af-

ter approx. 4 seconds the battery charge display

automatically turns off.

Battery charge:

When the first display element begins to flash

(0 –10%) the battery is almost empty and must

be recharged.

To maintain the accuracy of the display, occa-

sionally discharge the battery until the speed of

the machine is considerably reduced and the bat-

tery charge display has completely turned off.

Frequent recharging after short intervals of use

impairs the accuracy of the display.

■ Use the machine only with the auxiliary

handle 11.

Loosen the handle by turning to the left. Rotate

the auxiliary handle 11 and adapt to the working

position. Make sure that the clamping band 17 of

the auxiliary handle remains in the groove.

Firmly retighten the handle.

The drilling depth can be set with the depth

stop 12.

For this, press the push-button for the depth-stop

adjustment 4, adjust the required drilling depth X

and release the push-button for the depth-stop

adjustment 4 again.

The ribbing on depth stop 12 must point upwards.

■ Before any work on the machine itself, re-

move the battery.

With the SDS-plus tool holder, simpler and easier

tool changing is possible without additional aids.

☞

Grease the shank end of the tool regu-

larly.

The dust protection cap 1 largely prevents the

entry of drilling dust during operation. When in-

serting the tool, take care that the dust protection

cap 1 is not damaged.

A damaged dust protection cap should be

changed immediately. We recommend having

this carried out by an after-sales service.

☞

As a requirement of the system, the

SDS-plus tool must rotate freely. At no-load

speed, this leads to a certain amount of ra-

dial run-out.

This does not affect the accuracy of the drill

hole, as the bit is automatically centred dur-

ing drilling.

Inserting (see figure )

Clean and grease the shank end of the tool.

Insert the tool in a twisting manner into the tool

holder until it locks. Check if it has locked by pull-

ing the tool.

Removing (see figure )

Push back the locking sleeve 2 of the tool holder

and remove the tool.

Before Putting into Operation

0 – 10 %

10 – 20 %

20 – 40 %

40 – 60 %

60 – 80 %

80 – 100 %

9 8

Auxiliary Handle/Depth Stop

(see figure )

Changing the Tool

15 • 1 619 929 589 • TMS • 08.08.02

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GBH 24,0 VFR in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GBH 24,0 VFR Manual

Product: