Manual Bosch gbh 2 26 (page 23 of 139) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

388862

Zoom out

Zoom in

1/139

English | 23

Bosch Power Tools 1 619 929 726 | (14.11.07)

Note: If the tool holder was opened to the stop,

then the latching noise possibly may be heard

while closing the tool holder and the tool holder

will not close.

In this case, turn the front sleeve 21 once in the

opposite direction of the arrow. Afterwards, the

tool holder can be closed (tightened) again.

Turn the mode selector switch 11 to the “drill-

ing” position.

Removing Drilling Tools without SDS-plus

(GBH 2-26 DFR) (see figure I)

Firmly hold the retaining ring 22 of the quick

change chuck. Open the tool holder by turning

the front sleeve 21 in the direction of the arrow

until the tool can be removed.

Dust Extraction with the Dust

Extraction Attachment (Accessory)

f Dusts from materials such as lead-containing

coatings, some wood types, minerals and

metal can be harmful to one’s health. Touch-

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

tions of the user or bystanders.

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

– Use dust extraction whenever possible.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Mounting the Dust Extraction Attachment

(see figure J)

For dust extraction, the dust extraction attach-

ment (accessory) is required. When drilling, the

dust extraction attachment retracts so that the

attachment head is always close to the surface

at the drill hole.

Press the button for depth stop adjustment 12

and remove the depth stop 13. Press button 12

again and insert the dust extraction attachment

into the auxiliary handle 14 from the front.

Connect an extraction hose (diameter 19 mm,

accessory) to the extraction sleeve 23 of the

dust extraction attachment.

The vacuum cleaner must be suitable for the ma-

terial being worked.

When vacuuming dry dust that is especially det-

rimental to health or carcinogenic, use a special

vacuum cleaner.

Adjusting the Drilling Depth on the Dust

Extraction Attachment (see figure K)

The required drilling depth X can also be adjust-

ed when the dust extraction attachment is

mounted.

Insert the SDS-plus drilling tool to the stop into

the SDS-plus tool holder 3. Otherwise, the mov-

ability of the SDS-plus drilling tool can lead to

incorrect adjustment of the drilling depth.

Loosen the wing bolt 27 on the dust extraction

attachment.

Without switching the power tool on, apply it

firmly to the drilling location. The SDS-plus drill-

ing tool must face against the surface.

Position the the guide pipe 28 of the dust ex-

traction attachment in its holding fixture in such

a manner that the head of the dust extraction at-

tachment faces against the surface to be drilled.

Do not slide the guide pipe 28 further over the

telescopic pipe 26 of the dust extraction attach-

ment than required, so that as much as possible

of the scale 26 on the telescopic pipe remains

visible.

Retighten the wing bolt

27 again. Loosen the

clamping screw 24 on the depth stop of the dust

extraction attachment.

Move the depth stop 25 on the telescopic pipe

26 in such a manner that the clearance X shown

in the figure corresponds with the required drill-

ing depth.

Tighten the clamping screw 24 in this position.

OBJ_BUCH-279-002.book Page 23 Wednesday, November 14, 2007 12:41 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gbh 2 26 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch gbh 2 26 Manual

Product: