544359
216
Zoom out
Zoom in
Previous page
1/246
Next page
216 | 中文
1 609 929 T80 | (17.4.09) Bosch Power Tools
安装加长件测量 (参考插图 FH
必须在仪器上安装加长件 3 以方便测量,如果仪器的放置面长度比
折叠臂 1 短时。
安装好加长件 3 (参考 " 安装加长件 ",页数 214)。把主臂 4 和加
长件平放或者靠在测量边缘上。
此时显示屏上出现的测量值,即为主臂和折叠臂之间的角度 w
可以参考以下的运算方法,算出主臂和加长件之间的角度 v :
v =180°
w
操作模式 " 单斜切角 "
操作模式 " 单斜切角 " ("Simple MTR") 可以用来进行切割角 "MTR"
的运算,使用时机是当您想组合两块有相同斜切角的工件,而该工
件组合后的外角角度 x 小於 180 (例如针对地板的修边木条、
楼梯上的柱子或相框等)
如果要在角落组合两个工件 (例如地板的修边木条) 得把主臂和
折叠臂靠在角落上测量角度 x。如果是指定好的角度 (例如相框)
那麽要打开主臂和折叠臂至指定的角度出现在仪器的显示屏上为止。
运算出来的是水平斜切角 "MTR" ("Miter Angle": 水平斜切角 ), 也就是
必须从两个工件上切除的角度。锯割此斜切角时,锯刀必须和工件
垂直 (垂直的斜切角是 0 度)
按下按键 10,至少按住 1 秒钟。接著显示屏上会出现计算出来的水
平斜切角 "MTR" (即随后要在介铝机上设定的斜切角值),以及指
示灯 "MTR"
测量所得或者设定的外角角度如果 x 大于 180 度,在按下按键 10
2 秒钟之后,显示屏上会出现错误讯号 "
––––",接著仪器会转换
" 基本测量 " 的操作模式。
轻按按键 10,不可以超过 1 秒钟, 以便从 " 单斜切角 " 的操作模式
回到 " 基本测量 " 的操作模式。
指示: 计算出来的水平斜切角 "MTR" 能够直接使用在介铝机上,前
提是介铝机的垂直切角必须设定在 0 度上。如果介铝机的垂直切角
被设定为 90 度,则必须采用以下的运算方式换算锯割的角度:
90 仪器显示的角度 "MTR" = 必须在电锯上设定的角度。
x
˚
x
˚
MTR
MTR
MTR
MTR
OBJ_BUCH-958-001.book Page 216 Friday, April 17, 2009 10:26 AM
216


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GAM 220 MF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GAM 220 MF in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info