462320

Bosch EFLE61 Manual

12
Zoom out
Zoom in
Previous page
1/33
Next page
12
4. Measuring images
The measuring images can also be observed from the rear of the
aiming device by means of the deflection mirror (Fig. 10, No. 3).
Before every measurement the prerequisites given in Section 2
above must be complied with.
4.1 Headlamps with asymmetrical lower beam
With headlamps used for an asymmetrical lower beam, the lower
beam cut-off line must coincide with the boundary line to the left of
the center point. The point of intersection between the left-hand
part of the lower beam cut-off line (as horizontal as possible) and
the right-hand rising part of this line must be located on the vertical
line that passes through the center mark. In order to determine this
point of intersection more easily, the left-hand half of the handlamp
can be alternately masked and unmasked serveral times.
After the lower beam cut-off line has been set according to
specifications, the center of the high beam with headlamps on
which the lower beam and upper beam can be aimed together
must lie within the limit corners inscribed around the center mark.
With high-beam headlamps fitted with their own adjustment me-
chanisms, the center of the light beam must be positioned on the
center mark.
4.2 Headlamps with symmetrical lower beam, and fog
lamps
With headlamps used for a symmetrical lower beam and with fog
lamps, the highest part of the lower beam cut-off line must touch
the boundary line, must be as horizontal as possible across the
width of the test surface.
To the side, these headlamps must be aimed so that the distribution
of the light is as symmetrical as possible with respect to the vertical
line that passes through the center mark.
After the lower beam cut-off line has been set according to
specifications, the center of the high beam with headlamps on
which the lower beam and upper beam can be aimed together
must lie within the limit corners inscribed around the center mark
(see Fig. 8).
With high-beam headlamps fitted with their own adjustment me-
chanisms, the center of the light beam must be positioned on the
center mark (see Fig. 8).
Example: Boundary line for the lower eam cut-off with an asym-
metrical lower beam.
Fig. 7
Example: Center mark and boundary corners for the center of the
higt beam.
Fig. 8
Example: Boundary line for the lower beam cut-off with a symme-
trical lower beam and with fog lamps.
Fig. 9
4.3 Headlamps with inclination data
In the case of single-axle towing vehicles or machines with
headlamps permanently set to the lower beam and on which the
inclination of the light beam center is given, the center of the beam
must lie on the boundary line and on the vertical line that passes
through the center mark.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch EFLE61 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EFLE61 in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info