Manual Bosch EasyHedgeCut 12-450 (page 18 of 282) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

707792

Zoom out

Zoom in

1/282

18 | English

F 016 L81 736 | (23.5.17) Bosch Power Tools

AL 1115 CV

Flashing Battery Charge Indicator

The charging procedure is signalled by a

flashing battery charge indicator.

Continuous Lighting of the Battery Charge

Indicator

Continuous lighting of the battery

charge indicator indicates that the

battery is fully charged or that the

temperature of the battery is not with-

in the allowable charging temperature range, and cannot be

charged for this reason. The battery is charged as soon as the

allowable charging temperature range is reached.

When the battery is not inserted, continuous lighting of the

battery charge indicator indicates that the mains plug is in-

serted in the socket and that the battery charger is ready for

operation.

Charging Advice

With continuous or several repetitive charging cycles without

interruption, the charger can warm up. This is not meaningful

and does not indicate a technical defect of the battery charg-

er.

A significantly reduced working period after charging indi-

cates that the battery is used and must be replaced.

Working Advice

 Hold the garden product away from yourself. Stand in a

secure and stable position.

 When storing the product, do no store it hanging on the

front handle or switch.

Anti Blocking

If the blade stalls on a tough material, the load of the motor in-

creases. The intelligent micro-electronics senses this over-

load condition and repeatedly reverses the motor, in order to

prevent stalling and to cut the material through.

This audible reversing cut action continues for up to 3 s.

After cutting through, the garden product continues in its nor-

mal mode, or in case the overload condition continues the

blades automatically stop in the open position (e. g. in case a

piece of metal fence accidentally blocks the garden product).

Troubleshooting

Problem Possible Cause Corrective Action

Hedgecutter does not

operate

Battery discharged Recharge battery; also see “Battery Charging”

Safety switch not activated correctly see “Mounting and Operation” for correct use

Hedgecutter operates

intermittently

Internal wiring of machine damaged Contact Service Agent

On/Off switch defective Contact Service Agent

Motor reverses repeatedly then stops after 3 s. see “Working Advice” (Anti Blocking)

Motor runs but blades

remain stationary

Internal fault Contact Service Agent

Cutting blade hot Cutting blade blunt Have blade sharpened

Cutting blade has dents Have blade inspected/overhauled

Too much friction, due to lack of lubricant Apply lubricant spray (1 609 200 399)

Blade will not move Battery discharged Recharge battery; also see “Battery Charging”

Machine defective Contact Service Agent

Excessive vibrations/

noise

Machine defective Contact Service Agent

Cutting time per battery

charge too low

Too much friction, due to lack of lubricant Apply lubricant spray

Blade needs cleaning Clean blade

Battery not fully charged Recharge battery; also see “Battery Charging”

OBJ_BUCH-1685-008.book Page 18 Tuesday, May 23, 2017 2:11 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EasyHedgeCut 12-450 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch EasyHedgeCut 12-450 Manual

Product: