766864

Bosch EasyCut Grind Manual

22
Zoom out
Zoom in
Previous page
1/247
Next page
22 | English
It is therefore important to observe the permissible rota-
tional/circumferential speed on the label of the abrasive
tool.
max.
[mm] [mm]
D d [min-1] [m/s]
50 10 30,600 80
Selecting the Grinding/Cutting Disc
Grinding tool Material
Carbide Multi Ma-
terial Disc Wood (with nails),
plastic, PVC, com-
posite materials,
acrylic glass
Bonded Metal Cut-
ting Disc Metal, aluminium,
copper
Sanding plate with
abrasives Wood, metal
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one’s
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
uAvoid dust accumulation at the workplace. Dust can
easily ignite.
Operation
Start-up
Switching on/off
To unlock the power tool, press the lock-off button(4). The
status LED(1) lights up green. Then press the on/off
switch(5) and keep it pressed down to switch on the power
tool. While the status LED(1) is lit green, the power tool is
unlocked.
To switch off the power tool, release the on/off switch(5).
Then press the lock-off button(4) to lock the power tool. If
the power tool has not been switched on for longer than five
minutes, it will be locked automatically.
If the power tool does not switch off after releasing the on/
off switch(5), press the lock-off button(4).
uAlways check abrasive tools before using them. The
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use. Damaged
abrasive tools can burst apart and cause injuries.
Working Advice
uClamp the workpiece if it is not secure under its own
weight.
uDo not load the power tool so heavily that it comes to a
stop.
uIf the power tool has been subjected to a heavy load,
continue to run it at no-load for several minutes to
cool down the accessory.
uDo not use the power tool with a cut-off stand.
uWhen cutting lightweight materials, take into account
the statutory provisions and recommendations of the
material manufacturer.
uDo not touch grinding and cutting discs until they have
cooled down. The discs can become very hot while work-
ing.
Cutting metal
When carrying out abrasive cutting, use a moderate feed
that is suited to the material being machined. Do not exert
pressure on the cutting disc and do not tilt or swing the
power tool.
Do not attempt to reduce the speed of a cutting disc coming
to a stop by applying pressure from the side.
The power tool must always work in an up-grinding motion.
Otherwise there is a risk that it will be pushed uncontrolled
out of the cut.
For best results when cutting profiles and rectangular
tubing, start at the smallest cross section.
Information on structural design
Slots in load-bearing walls are subject to DIN 1053 part 1 or
country-specific regulations. These regulations must be ob-
served under all circumstances. Seek advice from the re-
sponsible structural engineer, architect or construction su-
pervisor before starting work.
Cutting aid (seefigureE)
The cutting aid(14) allows you to make a precise cut when
separating materials. Ensure that the cutting aid (14) is
firmly engaged before making the cut. To do this, turn the
cutting aid(14) together with the hood(7) so that the snap-
in fin(17) engages in the recess(16).
Transportation cover (seefigureF)
Fit the transportation cover(13) to transport the power
tool. This serves to prevent injuries and damage.
1 609 92A 6EL | (04.02.2021) Bosch Power Tools
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch EasyCut Grind at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EasyCut Grind in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 5,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info