697149

Bosch EasyControl Adapter OT-iRT-On-Off Manual

17
Zoom out
Zoom in
Previous page
1/80
Next page
6720821559 (2017/06)EasyControl Adapter OT-iRT/On-Off
Installation | 17
To dispose of old electrical or electronic devices, you should
use the return and collection systems put in place in the country
concerned.
4 Installation
4.1 Inspection beforehand
▶ Before installation, check that the combination of the
thermostat, the EasyControl adaptor and the boiler is
possible.
The minimum requirements for installation of this product are:
• 2-wire cable with the boiler that is suitable for the use of the
EasyControl adaptor.
4.2 Installation
▶ Ensure that the cable length between the EasyControl
adaptor and the boiler is max. 3 metres, since long data
cables can cause faults.
▶ Open the EasyControl adaptor casing ( fig. 3).
▶ Mark the bore holes by hand at the centre- to centre
distance between the slotted holes.
▶ Install the product using the provided screws and rawl
plugs.
▶ Tighten the screws finger-tight.
4.3 Electrical Connection
See the installation instructions for the boiler for more
information on connecting the thermostat.
Thermostat and boiler connection
The “thermostat” and “boiler” cable clamps are not polarity
sensitive.
▶ Remove the boiler plug from the socket.
▶ Disconnect the thermostat.
▶ Cut the 2-wire cable between the boiler and the
thermostat.
▶ Connect the part of the 2-wire cable that connects to the
boiler to the “boiler” cable clamps.
▶ Connect the part of the 2-wire cable that connects to the
thermostat to the “thermostat” cable clamps.
Bus connection
The bus is connected in the following way ( fig. 4):
[1] base plate
[2] thermostat or EMS module(s)
[3] EasyControl adaptor
[4] boiler
[5] boiler 2-wire cable
[6] power adaptor
[7] thermostat 2-wire cable
Zero volt contact
An on-off switching unit can be connected through the zero volt
contact ( fig. 5):
[1] normally open connection (NO)
[2] normally closed connection (NC)
[3] common (C)
The default connection is C-NO. Following a heat demand, the
NO contact closes.
▶ Close the EasyControl adaptor casing ( fig. 6).
▶ Connect the power adaptor to the EasyControl adaptor.
5 Commissioning
▶ Position the thermostat.
▶ Insert the power adaptor into a socket.
▶ Insert the boiler plug into a socket.
▶Turn on the boiler.
The EasyControl adaptor will start initialising ( fig. 7).
The steps in table 1 are run through automatically.
# LED indication The EasyControl adaptor:
1 Flashing red … is receiving power and is waiting
for protocol detection.
2 Flashing blue … is processing protocol detection.
3 Constantly blue … has detected a supported protocol
and is initialising the internal
database.
4 Constantly green … has received data from the boiler
as well as from the thermostat.
5 Constantly red … has detected an error during
communication.
6 Dimmed green … is in operation.
Table 1 LED indication during initialisation
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch EasyControl Adapter OT-iRT-On-Off at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EasyControl Adapter OT-iRT-On-Off in the language / languages: All languages as an attachment in your email.

The manual is 4,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info