Manual Bosch EasyAquatak 120 (page 17 of 282) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

708247

Zoom out

Zoom in

1/282

English | 17

Bosch Power Tools F 016 L81 747 | (7.8.17)

Working Advice

General

Ensure that the pressure washer is on level ground.

Do not overreach with the high pressure hose or move the

pressure washer by pulling the hose, this could cause the ma-

chine to become unstable and fall over.

Do not kink or drive a motor vehicle over the high pressure

hose. Do not expose the high pressure hose to sharp edges or

corners.

Never use a roto nozzle to clean motor vehicles.

Working advice for cleaning with detergents

 Only use cleaning agents suitable specifically for high

pressure washers.

We recommend that you use detergent sparingly for the sake

of the environment. Observe the recommended dilution on

the detergent label.

Recommended cleaning method

Step 1: Attach the fan nozzle and remove the heavy dirt.

Step 2: Attach the foam bottle and spray on the detergent

sparingly.

Step 3: Rinse off the loosened dirt and detergent with the fan

nozzle.

Note: When cleaning vertical surfaces, apply the detergent

from bottom to top. When rinsing off, work from top to bot-

tom.

Use with alternative water sources

The power washer is self-priming and enables water to be

drawn in from containers or natural water sources. It is IM-

PORTANT that the water filter is in clean condition when in-

serting it at the water inlet, and that only clean water is drawn

in.

Open tanks/containers and natural water sources

Use the Self Priming accessory kit comprising:

– Inlet strainer with non return valve

–3m reinforced supply hose

– Universal coupling to the pressure washer

This enables the pressure washer to draw water up to 0.5 m

above the water level in the source in approximately 15 sec-

onds.

Fully immerse the 3 m hose into the water to displace the air

in the hose. Connect the 3 m hose to the power washer and

make sure that the inlet strainer remains under water.

With the spray gun removed, switch the power washer on and

operate it until water flows uniformly out of the high-pressure

hose. If no water is coming out of the high-pressure hose after

25 seconds, switch the power washer off and check all con-

nections. As soon as water flows out of the high-pressure

hose, switch the power washer off and connect the spray gun

and spray lance to begin with the work.

It is important that hose and couplings are of good quality and

are tightly connected, and that the seals are undamaged and

properly inserted. Loose connections can impede the priming

(drawing in).

Water Tanks with outlet connections

When connecting the pressure washer to a water tank with a

suitable tap outlet, first connect the supply hose (not provid-

ed) to the tank outlet, open the tap to allow the water to dis-

place all the air in the hose and then connect to the pressure

washer.

Troubleshooting

Problem Possible Cause Corrective Action

Motor refuses to start Plug not connected Connect plug

Mains socket faulty Use another socket

Fuse faulty/blown Replace fuse

Extension cable damaged Try without extension cable

Motor protector has activated Allow to cool for 15 minutes

Frozen Wait for pump/water supply hose/acces-

sory to thaw

Motor stops Fuse faulty/blown Replace fuse

Wrong mains voltage Check that mains voltage corresponds to

specifications on the model tag

Motor protector has activated Allow to cool for 15 minutes

Fuses blow Fuses incorrectly rated Change to a mains supply higher than the

pressure washer amp consumption

Motor starts but no pressure Nozzle partly blocked Clean nozzle

OBJ_BUCH-2949-002.book Page 17 Monday, August 7, 2017 2:55 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch EasyAquatak 120 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 14,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch EasyAquatak 120 Manual

Product: