en Operating the appliance
8
Control panel model 2
Setting the fan
Switching on
1. Touch the # symbol.
The fan starts at fan setting 2.
2. Use the rotary selector to select the fan setting.
Note: Turn the rotary selector clockwise to set a
higher fan setting, and turn it anti-clockwise to set a
lower fan setting. The selected fan setting is shown
in the display.
Switching off
Touch the # symbol.
Intensive setting
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
Switching on
Turn the rotary selector until ˜‚ or ˜ƒ is displayed.
Note: After approx. 6minutes, the extractor hood
automatically switches back to fan setting 3.
Switching off
If you want to end the intensive mode before the set
time has elapsed, turn the rotary selector anti-clockwise.
Intermediate position for the glass front
On some appliances, the glass front can be adjusted to
an intermediate position. The intermediate position can
be used for eliminating particularly strong cooking
smells and large amounts of steam.
Take hold of the glass front in the centre and open it
carefully.
Automatic mode
Switching on
Touch the
> symbol.
The optimum fan setting (‘‚-‘†) is set automatically
using the PerfectAir sensor.
Switching off
Touch the > symbol to switch off automatic mode.
The fan will switch itself off automatically if the
PerfectAir sensor detects no further change in the air
quality in the room. The appliance will switch back to
the fan setting that was last selected.
Automatic mode can run for a maximum of 4 hours.
Sensor control
In automatic mode, the PerfectAir sensor in the
extractor hood detects the intensity of the cooking and
roasting odours. Depending on the setting of the
PerfectAir sensor, the fan automatically switches itself to
another fan setting.
Possible sensor settings:
Default sensitivity setting: ‡
Lowest sensitivity setting: ‚
Highest sensitivity setting: ‚‹
If the sensor controller responds too strongly or not
enough, it can be changed accordingly:
1. Touch and hold the > symbol when the fan is
switched off. The setting will be displayed.
2. Use the control ring to select the setting you require.
3. Take your finger off the > symbol.
Symbol Explanation
#
Fan on/off
:
Fan settings
>
Automatic mode
y
Fan run-on
E
Metal grease filter saturation indicator
F
Activated charcoal filter saturation indicator
l
Decorative LED lighting
B
Light on/off/dimming
Indicator Explanation
D
Home Connect
‚-„
Fan settings
˜‚, ˜ƒ
Intensive mode
/
Fan run-on in minutes
E
Metal grease filter saturation indicator
F
Activated charcoal filter saturation indicator
Operating the appliance en
9
Fan run-on time
Switching on
Touch the
y symbol.
The fan runs at fan setting 1.
The remaining minutes of the run-on time are shown in
the display.
After approx. 10minutes, the fan switches off
automatically.
Note: You can use the rotary selector to adjust the run-
on time (‚ to ŠŠ minutes).
Switching off
Touch the y symbol.
This immediately stops the fan run-on. The appliance
switches to the fan setting that was previously set.
Decorative LED lighting
The decorative LED lighting can be switched on and off
independently of the fan.
Touch the
l symbol.
Setting the brightness
Press and hold the l symbol until the required
brightness is reached.
Setting the colour
1. Switch off the fan.
2. Touch the l symbol.
3. Use the control ring to select the colour you want.
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
Lighting
The lighting can be switched on and off independently
of the fan.
Touch the
B symbol.
Setting the brightness
Press and hold the
B symbol until the required
brightness is reached.
Saturation display
If the metal grease filters or activated charcoal filter are/
is saturated, the corresponding symbols flash once the
appliance has been switched off:
■ Metal grease filter: E
■ Activated charcoal filter: F
■ Metal grease filter and activated charcoal filter: E
and F
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced. ~ "Cleaning and maintenance" on page 13
The saturation displays can be reset while they are
flashing. To do this, touch the
E or F symbol.
Switching over the display for the air circulation
mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
■ The extractor hood must be connected and switched
off.
■ Touch and hold the : symbol. Use the rotary
selector to change the display to 2. Take your finger
off the : symbol. This switches the electronic
controller over to air recirculation mode (filters that
cannot be regenerated).
■ Touch and hold the : symbol. Use the rotary
selector to change the display to 3. Take your finger
off the : symbol. This switches the electronic
controller over to air recirculation mode (filters that
can be regenerated).
■ Repeatedly touching and holding the : symbol and
changing the display to "1" switches the electronic
controller back to air extraction mode.
Audible signal
Switching on
Touch and hold the
# and y symbols at the same
time for approximately three seconds when the fan is
switched off. As confirmation, an audible signal sounds
and ‚ is shown in the display.
Switching off
Touch and hold the
# and y symbols at the same
time for approximately three seconds when the fan is
switched off. As confirmation, ‹ is shown in the display.
