en Operating the appliance
6
1Operating the appliance
Oper at i ng t he appl i ance
These instructions apply to several appliance variants.
It is possible that individual features are described
which do not apply to your appliance.
Note: Switch on the extractor hood when you start
cooking and switch it off again several minutes after you
have finished cooking. This is the most effective way of
removing the kitchen fumes.
Control panel model 1
Setting the fan
Switching on
Touch the
# symbol.
The fan will start at fan setting 2.
Selecting a fan setting
Select the fan setting.
Switching off
Touch the # symbol.
Intensive setting
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
Switching on
Touch the
C or D symbol.
Note: After approx. 6minutes, the extractor hood
automatically switches back to fan setting 3.
Switching off
If you want to end intensive mode before the preset
time expires, touch the symbol for the required fan
setting.
Intermediate position for the glass front
On some appliances, the glass front can be adjusted to
an intermediate position. The intermediate position can
be used for eliminating particularly strong cooking
smells and large amounts of steam.
Take hold of the glass front in the centre and open it
carefully.
Fan run-on time
Switching on
Touch the
y symbol.
The fan will run at fan setting 1.
After approximately 10minutes, the fan will switch itself
off automatically.
Switching off
Touch the y symbol.
This immediately stops fan run-on.
Automatic mode
Switching on
1. Touch the # symbol.
The fan will start at setting 2.
2. Touch the > symbol.
The optimum fan setting is set automatically using
the PerfectAir sensor.
Switching off
Touch # or any fan setting to switch off automatic
mode.
The fan switches itself off automatically if the PerfectAir
sensor detects no further change in the air quality in the
room.
Automatic mode can run for a maximum of 4 hours.
Symbol Explanation
#
Fan on/off
1-3 Fan settings
C
Intensive mode 1
D
Intensive mode 2
y
Fan run-on
>
Automatic mode
#
Metal grease filter/activated charcoal filter saturation
indicator
D
Home Connect
B
Light on/off/dimming
Operating the appliance en
7
Sensor control
In automatic mode, the PerfectAir sensor in the
extractor hood detects the intensity of the cooking and
roasting odours. Depending on the setting of the
PerfectAir sensor, the fan automatically switches itself to
another fan setting.
Possible sensor settings:
Default sensitivity setting:
„ (fan setting 3)
Lowest sensitivity setting: ‚ (fan setting 1)
Highest sensitivity setting: † (fan setting D)
If the sensor controller responds too strongly or not
enough, it can be changed accordingly:
1. Touch and hold the > symbol when the fan is
switched off. The setting will be displayed.
2. The sensor controller setting can be changed by
touching symbols 1, 2, 3,
C or D.
3. Take your finger off the > symbol.
Saturation display
If the metal grease filters or activated charcoal filter are/
is saturated, the corresponding symbols will flash once
the appliance has been switched off:
■ Metal grease filter: # and 1
■ Activated charcoal filter: # and 2
■ Metal grease filter and activated charcoal filter: #,
1and 2
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced. ~ "Cleaning and maintenance" on page 13
The saturation indicators can be reset while they are
flashing. To do this, touch the # symbol.
Switching over the display for air recirculation mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
■ The extractor hood must be connected and switched
off.
■ Touch and hold the D symbol. Touch the "2"
symbol.Take your finger off the D symbol. This
will switch the electronic controller over to air
recirculation mode (filters that cannot be
regenerated).
■ Touch and hold the D symbol. Touch the "3"
symbol.Take your finger off the D symbol. This
will switch the electronic controller over to air
recirculation mode (filters that can be regenerated).
■ Repeatedly touching and holding the D symbol
and touching the "1" symbol switches the electronic
controller back over to air extraction mode.
Lighting
The lighting can be switched on and off independently
of the fan.
Touch the
B symbol.
Setting the brightness
Press and hold the B symbol until the required
brightness is reached.
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
Audible signal
Switching on
Touch and hold the
# and y symbols at the same
time for approximately 3seconds when the fan is
switched off. An audible signal will sound as an
acknowledgement.
Switching off
Touch and hold the # and y symbols at the same
time for approximately 3seconds when the fan is
switched off. An audible signal will sound as an
acknowledgement.
