746998
9
Zoom out
Zoom in
Previous page
1/24
Next page
en Operating the appliance
8
Sensor control
In automatic mode, the PerfectAir sensor in the
extractor hood detects the intensity of the cooking and
roasting odours. Depending on the setting of the
PerfectAir sensor, the fan automatically switches itself to
another fan setting.
Possible sensor settings:
Default sensitivity setting:
(fan setting 3)
Lowest sensitivity setting: (fan setting 1)
Highest sensitivity setting: (fan setting D)
If the sensor controller responds too strongly or not
enough, it can be changed accordingly:
1. Touch and hold the > symbol when the fan is
switched off. The setting will be displayed.
2. The sensor controller setting can be changed by
touching symbols 1, 2, 3,
C or D.
3. Take your finger off the > symbol.
Saturation display
If the metal grease filters or the activated charcoal filter
are/is saturated, the corresponding symbols flashes
after the appliance is switched off:
Metal grease filters: # and 1
Activated charcoal filter: # and 2
Metal grease filter and activated charcoal filter: #,
1 and 2
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced. ~ "Cleaning and maintenance" on page 12
Note: The saturation indicator does not apply for non-
renewable activated charcoal filters that are inserted
downstream of the metal grease filter. These activated
charcoal filters must be replaced twice a year.
The saturation indicators can be reset while they are
flashing. To do this, touch the # symbol.
Switching over the display for air recirculation mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
The extractor hood must be connected and switched
off.
Touch and hold the D symbol. Touch the "2"
symbol.Take your finger off the D symbol. This
will switch the electronic controller over to air
recirculation mode (filters that cannot be
regenerated).
Touch and hold the D symbol. Touch the "3"
symbol.Take your finger off the D symbol. This
will switch the electronic controller over to air
recirculation mode (filters that can be regenerated).
Repeatedly touching and holding the D symbol
and touching the "1" symbol switches the electronic
controller back over to air extraction mode.
Lighting
The lighting can be switched on and off independently
of the fan.
Touch the
B symbol.
Setting the brightness
Press and hold the B symbol until the required
brightness is reached.
Audible signal
Switching on
Touch and hold the
# and y symbols at the same
time for approximately 3 seconds when the fan is
switched off. An audible signal will sound as an
acknowledgement.
Switching off
Touch and hold the # and y symbols at the same
time for approximately 3 seconds when the fan is
switched off. An audible signal will sound as an
acknowledgement.
Connecting to a hob en
9
eConnecting to a hob
Connect i ng to a hob
You can connect this appliance to a hob (if the hob
supports connection to the appliance) and then control
the functions of the hood via your hob.
Appliances can be connected to each other in different
ways:
Home Connect
Two appliances can be connected using the Home
Connect app provided that both of them are Home
Connect compatible.
Refer to the Home Connect documents supplied for
more information.
Connecting appliances directly
If the appliance is connected directly to a hob, it cannot
be connected to your home network as well. The
appliance will function as an extractor hood that is not
connected to the network and you can continue to
operate it via the control panel.
Connecting appliances via your home network
If the appliances are connected to each other via your
home network, both the hood controls on the hob and
Home Connect can be used to operate the appliance.
Notes
Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the hob.
If the extractor hood is being operated by means of
the controls on the hood itself, this mode of
operation always has priority. It is not possible to use
the hood controls on the hob during this time.
Setting up a connection
The hood must be switched off before you can connect
the hob and extractor hood.
Connecting directly
Make sure that the hob is switched on and is in search
mode.
To do this, refer to the section entitled "Connecting to
the extractor hood" in the instruction manual for your
hob.
Notes
Before connecting the appliance, reset all existing
connections to the WiFi or other appliances.
If your extractor hood is connected directly to the
hob, it cannot be connected to your WiFi as well and
you will not be able to use Home Connect.
Press and hold the
D symbol until it starts to flash.
The extractor hood has been connected to the hob
when the D symbol stops flashing and remains
continuously lit.
Connecting via your home network
Follow the instructions in the section entitled "Automatic
login to your home network" or "Manually logging into
your home network" ~ "Home Connect" on page 10
Once the extractor hood is connected to your home
network, you can connect to the hob via the Home
Connect app. To do this. follow the instructions on your
mobile device.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch DWB98PR50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch DWB98PR50 in the language / languages: English as an attachment in your email.

The manual is 1,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch DWB98PR50

Bosch DWB98PR50 User Manual - German - 24 pages

Bosch DWB98PR50 User Manual - Dutch - 24 pages

Bosch DWB98PR50 User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info