657566
23
Zoom out
Zoom in
Previous page
1/141
Next page
English2
Bosch eBike Systems 0 276 001 YYY | (12.10.12)
Technical Data
Assembly
Inserting and Removing the Battery Pack
For inserting and removing the battery pack in/from the
eBike, please read and observe the battery pack operating in-
structions.
Inserting and Removing the Drive HMI
(see figure A)
To insert the drive HMI 3, slide it from the front into the
holder 4.
To remove the drive HMI 3, press the lock latch 15 and slide
the drive HMI toward the front out of the holder 4.
Remove the drive HMI when parking the eBike, so that
the drive cannot be used by unauthorised persons.
Without the drive HMI, the eBike system cannot be
switched on.
The drive HMI can also be secured in
the holder against re-
moving. For this, remove the holder 4 from the handlebar. In-
sert the drive HMI into the holder. Screw the locking screw 16
from below into the corresponding thread in the holder.
Mount the holder onto the handlebar again.
Checking the Speed Sensor (see figure B)
The speed sensor 17 and its spoke magnet 18 must be
mounted in such a manner that the spoke magnet, after a turn
of the wheel, moves past the speed sensor with a clearance of
at least 5 mm, yet no more than 17 mm.
Note: If the clearance between speed sensor 17 and spoke
magnet 18 is too small or too large, or if the speed sensor 17
is not properly connected, the speed indication e w
ill fail, and
the eBike drive will operate in emergency mode.
In this case, loosen the screw of the spoke magnet 18 and fas-
ten the spoke magnet to the spoke in such a manner that it
runs past the mark of the speed sensor at the correct clear-
ance. When the speed is still not being indicated in the speed
indication e after this, please refer to an authorised bicycle
dealer.
Operation
Initial Operation
Requirements
The eBike system can only be activated when the following re-
quirements are met:
–A sufficiently charged battery pack is inserted (see operat-
ing instructions of the battery pack).
–The drive HMI is properly inserted in the holder (see “In-
serting and Removing the Drive HMI”, page English–2).
–The drive HMI is properly connected (see “Checking the
Speed Sensor”, page E
nglish–2).
Switching the eBike System On/Off
Options for switching on the eBike system:
–If the drive HMI is already switched on when inserting it in
the holder, the eBike system is automatically switched on.
–When the drive HMI and the battery pack are inserted,
briefly press the On/Off button 5 of the drive HMI once.
–When the drive HMI is in
serted, press the On/Off button of
the battery pack (see battery pack operating instructions).
Note: When switching on the eBike system, the pedals of the
eBike must not be subject to load, as otherwise the motor out-
put capacity will be limited. The error message “Release ped-
al” is displayed in text indication c.
If the eBike system was inadvertently switched on with load
applied to the pedals, th
en switch it off and then on again
without load.
The drive is activated as soon as you step into the pedals (ex-
cept when in push-assistance mode, see “Switching the Push-
assistance mode On/Off”, page English–4). The motor out-
put depends on the settings of the drive HMI.
Drive Unit Drive Unit Cruise
Article number
0 275 007 006/
0 275 007 007
Power output
W250
Output torque, max.
Nm50
Rated voltage
V 36
Operating temperature
°C –5...+40
Storage temperature
°C –10...+50
Degree of protection
IP 54 (dust and splash
water protected)
Weight, approx.
kg 4
Drive HMI Intuvia
Article number
1 270 020 903
Max. charging current, USB
connection.
mA 500
Charging voltage, USB con-
nection
V 5
Operating temperature
°C –5...+40
Storage temperature
°C –10...+50
Degree of protection
IP 54 (dust and splash
water protected)
Weight, approx.
kg 0.15
Lighting*
Rated voltage V 6
Power output
–Front light
Rear light
W
W
2.7
0.3
* Not possible via the eBike battery pack in all country-specific versions,
depending on the statutory regulations
OBJ_BUCH-1407-003.book Page 2 Friday, October 12, 2012 1:01 PM
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Drive Unit Cruise at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Drive Unit Cruise in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 9,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info