109607

Bosch DKE 975 C Manual

22
Zoom out
Zoom in
Previous page
1/48
Next page
22
en
Prior to installation
Round pipes:
We recommend
Internal diameter: 150 mm (at least 120 mm).
Flat ducts must have an internal crosssection
that equates to that of round pipes.
There should be no sharp bends.
ø 120 mm approx. 113 cm
2
ø 150 mm approx. 177 cm
2
If pipes have different diameters: Insert seal-
ing strip.
For exhaust-air mode, ensure that there is an
adequate supply of fresh air.
Connecting a Ø 150 mm exhaust-air pipe:
Mount the pipe directly onto the air outlet on the
hood.
Connecting a Ø 120 mm exhaust-air pipe:
Attach the reducing con-
nector directly to the air
pipe.
Attach the exhaust-air
pipe to the reducing con-
nector.
Circulating-air mode
With activated carbon fi lter if ex-
haust-air mode is not possible.
The complete installation set can
be obtained from specialist outlets.
The corresponding accessory num-
bers can be found at the end of these
operating instructions.
Electrical connection
WARNING: THIS APPLIANCE MUST BE
EARTHED
IMPORTANT: Fitting a Different Plug:
The wires in the mains lead are coloured in accord-
ance with the following code:
Green and Yellow – Earth
Blue – Neutral
Brown – Live
If you fi t your own plug, the colours of these wires
may not correspond with the identifying marks on
the plug terminals.
This is what you have to do:
1. Connect the green and yellow (Earth) wire to
the terminal in the plug marked ‘E’ or with the
symbol ( ), or coloured green or green and yel-
low.
2. Connect the blue (Neutral) wire to the terminal
in the plug marked ‘N’ or coloured black.
3. Connect the brown (Live) wire to the terminal
marked ‘L’, or coloured red.
The extractor hood should only be connected to an
earthed socket that has been installed according to
relevant regulations.
If possible, site the earthed socket directly behind
the chimney panelling.
The earthed socket should be connected via its
own circuit.
If the earthed socket is no longer accessible fol-
lowing installation of the extractor hood, ensure
that there is a permanently installed disconnec-
tor.
If it is necessary to wire the extractor hood di-
rectly into the mains:
The extractor hood should only be connected to the
electricity supply by a properly qualifi ed electrician.
A separator must be installed in the household
circuit. A suitable separator is a switch that has a
contact gap of more than 3 mm and interrupts all
poles. Such devices include circuit breakers and
contactors.
If the connecting cable for this appliance
is damaged, the cable must be replaced by the
manufacturer or his customer service or a similarly
qualifi ed person in order to prevent serious injury to
the user.
9
ø 120
Preparing the wall
The wall must be fl at and perpendicular.
Ensure that the wall is capable of providing a
fi rm hold for mounting screws and plugs.
Weight in kg: 20.
We reserve the right to construction changes within the context of technical
development.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch DKE 975 C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch DKE 975 C in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info