Manual Bosch Display Mount BDS3250 (page 7 of 28) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

780132

Zoom out

Zoom in

1/28

English – 1

Safety instructions

Read all the safety information and in-

structions. Failure to observe the safety in-

formation and follow instructions may result

in electric shock, fire and/or serious injury.

Save all safety warnings and instructions for future ref-

erence.

uThe contact surfaces of the display holder may be-

come very hot (>60°C). Allow the contact surfaces to

adjust to the ambient temperature before you touch

them. This is particularly important when using a Smart-

phoneGrip.

uKeep swallowable small parts away from small chil-

dren. There is a risk of serious injury.

uNever short-circuit the pins. The display holder may be

irreparably damaged and must then be replaced.

uEnsure that the contacts are free of dirt. By doing this,

you prevent malfunctions or damage.

uAfter a fall, check the display holder for sharp edges.

Replace it if required.

uDo not stand your bicycle upside down on its saddle

and handlebars if the on-board computer or its holder

protrude from the handlebars. This may irreparably

damage the on-board computer or the holder. Also re-

move the on-board computer before placing the bicycle

on a wall mount to ensure that the on-board computer

does not fall off or become damaged.

uObserve all national regulations which set out the ap-

proved use of eBikes.

uRead and observe the safety warnings and directions

contained in all the eBike system operating instruc-

tions and in the operating instructions of your eBike.

Product description and

specifications

Intended use

The display holder is intended to establish the mechanical

and electrical connection to a display or on-board computer.

Only original Bosch eBike components can be connected to

the display holder.

A display holder is not required for an eBike system to func-

tion.

Product features

The numbering of the components shown refers to the illus-

trations on the graphics pages at the beginning of the

manual.

(1) Display mount

(2) Adapter tray

(3) Clamp for holder

(4) Clamp screw

(5) Round rubber spacer

(6) 1-arm socket

(7) Screw for adjusting tilt

(8) Removal blocker

(9) Snap-in hook

(10) Connection cables

(11) Fastening screws for display mount

The display mount(1) can also be embedded in the bicycle

design.

Technical data

Display holder

Product code BDS3210

BDS3250

BDS3620

BDS3630

Output voltage V 4.75 to 5.4

Output current, max. A 1.5

Operating temperature °C –5 to +40

Storage temperature °C +10 to +40

Protection rating IP54

Fitting

Installation positions (seefigureA)

The 1-arm socket can be mounted at three different posi-

tions on the handlebars:

– In front of the handlebars ➀

– Over the stem ➁

– In the triangle between the stem and handlebar ➂

Note: In order to ensure clean cable routing, the appropriate

display mount must be used for each of the three different

positions: The BDS3210 display mount for in front of the

handlebars (electrical connections at the rear); the

BDS3250 display mount for over the stem or in the triangle

between the stem and handlebar (electrical connections at

the front).

If you want to change the installation position and you have

the correct display mount(1), you must first remove the 1-

arm socket(6) and re-mount it afterwards.

Note: Please be aware that there are two different handlebar

diameters (31.8mm and 35mm). Your bicycle retailer will

help you to select the correct components.

Mounting the display mount (seefigureB)

Insert the display mount(1) into the adapter tray(2). En-

sure that it is in the required installation position. Secure the

display mount(1) from below using the screws(11). When

Bosch eBike Systems 0 275 007 3S1 | (09.06.2021)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Display Mount BDS3250 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1.98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch Display Mount BDS3250 Manual

Product: