773187
7
Zoom out
Zoom in
Previous page
1/12
Next page
Cleaning and maintenance en
7
Saturation signal
The following will happen when the filters are saturated:
The ª symbol appears in the display: Clean the
metal grease filter
The symbol appears in the display and a signal
sounds: Replace the activated charcoal filter
See the "CleanAir air recirculation module" printed
supplement or the section entitled~ "Cleaning and
maintenance" on page 7
Resetting the saturation signal
When the fan is switched off, the signal is also switched
off.
The relevant filter(s) should be cleaned now if you have
not already done so.
Switching over the appliance to air recirculation
1. Switch off the appliance.
2. Press the $ and I* buttons on the control panel
at the same time until the indicator lights up.Then
release the buttons.
The indicator will go out shortly afterwards. The
electronic controller has now been switched over to air
recirculation mode.
Switching over the appliance to air extraction
Note: The default setting is air extraction mode.
1. Switch off the appliance.
2. Press the $ and I* buttons on the control panel
at the same time until the ª indicator lights up.Then
release the buttons.
The ª indicator will go out shortly afterwards. The
electronic controller has now been switched over to air
extraction mode.
2Cleaning and maintenance
Cl eani ng and mai nt enance
:Warning – Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
:Warning – Risk of electric shock!
Penetrating moisture may result in an electric shock.
Clean the appliance using a damp cloth only. Before
cleaning, pull out the mains plug or switch off the circuit
breaker in the fuse box.
:Warning – Risk of electric shock!
Do not use any high-pressure cleaners or steam
cleaners, which can result in an electric shock.
:Warning – Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
Cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Do not use any of the following:
Harsh or abrasive cleaning agents,
Cleaning agents with a high alcohol content,
Hard scouring pads or cleaning sponges,
High-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Follow all instructions and warnings included with the
cleaning agents.
Area Cleaning agent
Stainless
steel
Hot soapy water:
Clean with a dish cloth and then dry with a soft cloth.
Clean stainless steel surfaces in the grind direction only.
Special stainless steel cleaning products are available
from our after-sales service or from specialist retailers.
Apply a very thin layer of the cleaning product with a soft
cloth.
Painted
surfaces
Hot soapy water:
Clean using a damp dish cloth and dry with a soft cloth/
towel.
Do not use any stainless steel cleaners.
Alumin-
ium and
plastic
Glass cleaner:
Clean with a soft cloth.
Glass Glass cleaner:
Clean with a soft cloth. Do not use a glass scraper.
Controls Hot soapy water:
Clean using a damp dish cloth and dry with a soft cloth/
towel.
Risk of electric shock caused by penetrating moisture.
Risk of damage to the electronics from penetrating mois-
ture. Never clean operating controls with a wet cloth.
Do not use any stainless steel cleaners.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch DID09T951B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch DID09T951B in the language / languages: English as an attachment in your email.

The manual is 1.75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info