697302
12
Zoom out
Zoom in
Previous page
1/16
Next page
12
Service menu
CS200 – 6720830475 (2015/06)
7.1 Solar system settings
Fig. 8 Solar settings menu
If a solar system with extended functionality is installed,
corresponding menus and menu items become active. The
menus of the solar system are described in detail in the
operating instructions of the module installed (e.g. MS 200).
In the Solar settings menu with all solar systems the sub-
menus listed in Tab. 7 are available.
If the solar collector area is incorrectly set, the solar yield
displayed in the info menu is wrong as well.
Table 7 General settings for the solar system
7.2 Diagnosis
Fig. 9 Diagnosis menu
The Diagnosis service menu contains a number of tools for
diagnosis. Note that the menu items shown will vary depending
on the heating system.
7.2.1 Function tests
This menu can be used to test active system components
individually. If Enable function tests is set to Yes in this menu,
the normal heating operation is interrupted in the entire
system. All settings are saved. The settings in this menu are only
temporary and revert to the respective default settings as soon
as the Enable function tests is set to No or the Function test
menu is closed. The available functions and the possible
settings vary depending on the system installed.
A function test is performed by setting the parameters of the
listed component accordingly. You can check whether the
mixer, pump or valve responds appropriately by inspecting the
behaviour of the corresponding component.
The solar pump can be tested, for instance:
Off: The pump stops.
On: The pump starts.
7.2.2 Monitored values
System settings and measurements are displayed in this menu.
For example, the system can display whether the maximum
collector temperature or the current cylinder temperature has
been reached.
You can also call up detailed information on system parts, e.g.
the swimming pool. The information and values that are
provided depend on the system that has been installed.
Observe the technical documentation for modules and other
system components.
7.2.3 Fault displays
The current faults and the fault history can be called up in this
menu.
Table 8 Information in the fault display menu
7.2.4 System information
The software versions of the BUS nodes installed in the system
can be called up in this menu.
7.2.5 Maintenance
You can add a contact address in this menu. When the user
interface displays a fault code, the added address is also
displayed. The end customer can notify the installer to arrange
an appointment ( Chapter 9, page 14).
Menu item Purpose of the menu
Change solar
configuration
Graphical configuration of the solar
system
Current solar
configuration
Graphical representation of the
configured solar system
Solar parameters Settings for the installed solar system
Start solar thermal
system
Once all required parameters have been
set, the solar system can be started up.
0010003272-001
0010003114.001
Menu item Description
Active faults All current faults that are present in the
system are displayed here according to
their severity.
Fault history The last 20 faults are displayed here,
sorted in order of the time of occurrence.
The fault history can be deleted in the
Reset menu ( Chapter 7.2.6,
page 13).
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch CS 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch CS 200 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch CS 200

Bosch CS 200 User Manual - English - 12 pages

Bosch CS 200 User Manual - German - 12 pages

Bosch CS 200 Installation Guide - German - 20 pages

Bosch CS 200 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info