697302
8
Zoom out
Zoom in
Previous page
1/16
Next page
8
Commissioning
CS200 – 6720830475 (2015/06)
4.3 Operating the service menu
Closing and opening the service menu
Opening the service menu
Hold the menu key until the service menu is displayed.
Closing the service menu
If no sub-menu is open, press the Back key to switch to the
standard display.
-or-
Press and hold the Back key for a few seconds to switch to
the standard display.
Navigating through the menu
Turn the rotary control knob to highlight a menu or a menu
item.
Press the rotary control knob.
The menu or the menu item is displayed.
Press the Back key to return to the previous menu level.
Changing setting values
Selection
Turn the rotary control knob to highlight an entry.
Slider
Turn the rotary control knob to move the displayed sliding
scale and set the value between minimum and maximum.
Selection with slider
Turn the rotary control knob to highlight an entry.
Press the rotary control knob to confirm the selection.
The input field and the slider are enabled.
Turn the rotary control knob to set the setting value
between minimum and maximum.
Multiple selection
Turn the rotary control knob to highlight an entry.
Press the rotary control knob to select the entry.
Press the rotary control knob again to cancel the selection.
Repeat the action steps until the desired entries are
selected.
Time program
Turn the rotary control knob to highlight a switching time or
the corresponding operating mode.
Press the rotary control knob to activate the input field for
the switching time or the operating mode.
Turn the rotary control knob to change the setting value.
Confirming or rejecting the change
Rejecting the change
Press the rotary control knob to activate the marked entry
or to confirm the change.
Turn the rotary control knob to highlight Continue and
press the rotary control knob.
The Display switches to the previous menu level. The solar
controller operates with the modified setting.
Rejecting the change
Press the Back button.
4.4 Overview of the service menu
These instructions contain an overview of the menu structure.
More detailed information about the menu items and their
functions can be found in the technical documentation of the
installed solar modules (i.e. MS 200).
Table 5 Overview of the service menu
5 Commissioning
System schematics can be found in the technical
documentation of the modules MS 100/MS 200.
5.1 Overview of the commissioning steps
1. Ensure correct installation of Solar heating system
(observe instructions for all assemblies and components)
2. Initial charging with fluids and hydrostatic test
3. Electrical wiring
4. Coding of the modules (observe instructions of the
modules)
Menu and purpose of the menu Page
Commissioning 8
Start the configuration wizard, check and, if
necessary, adjust the most important settings for
the system.
Solar settings 12
Configuring the solar system
Diagnosis 12
System diagnosis:
Perform function test of individual
components (e.g. pumps).
Compare the set and actual values.
Display current faults and the fault history.
Display the software versions of all BUS
nodes.
Additional functions:
Enter installer address.
Calibrate the time.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch CS 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch CS 200 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch CS 200

Bosch CS 200 User Manual - English - 12 pages

Bosch CS 200 User Manual - German - 12 pages

Bosch CS 200 Installation Guide - German - 20 pages

Bosch CS 200 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info