809354

Bosch CRC R-1 Climate Room Control Manual

5
Zoom out
Zoom in
Previous page
1/16
Next page
Configuration to the wired room controller
61
Climate Room Control – 6721841498 (2022/04)
3.3 Electrical connection
WARNING
Risk to life from electric shock!
Touching live electrical parts can cause an electric shock.
▶ Before working on electrical parts, disconnect all phases of
the power supply (fuse/circuit breaker) and lock the
isolator switch to prevent unintentional reconnection.
3.3.1 Connect the the wired room controller
NOTICE
Damage to the wired room controller or wiring
▶ Do not jam wires during installation.
▶ To avoid water entering the wired room controller when
attaching the cabling ( Fig. 6), use trap [2] and putty [1]
to seal the plug-in connector.
▶ Cables must be securely attached and must not be under
tension.
NOTICE
Damage due to overvoltage
The wired room controller is designed for low voltage.
▶ Never bring the communication cable into contact with high
voltages.
Use the cable provided.
▶ If necessary, route an extension cable between the indoor
unit and installation location of the wired room controller.
▶ Connect the communication cable to the indoor unit or
connection module.
▶ Where applicable, connect the communication cable with
the wired room controller via an extension cable.
▶Fit the magnet ring.
▶ If possible, connect the earthing terminal lug.
▶ Insert the button battery into the holder [1].
4 Configuration to the wired room
controller
Call up the configuration menu and make the settings:
▶ Switch off the air conditioning system.
▶Keep theCOPY key pressed until a parameter appears in
the display.
If several indoor units are detected, the address (e.g. 00)
appears initially.
▶With the / or . key, select an indoor unit (00... 16) and
confirm with the key.
▶ Select a parameter with the / or . key and confirm with
the key.
▶ Press the / or . key to set the parameter and confirm it
with the key, or press the d key to cancel the setting.
To exit the configuration menu:
▶ Press the d key or wait for 15 seconds.
Make the settings in the configuration menu:
▶ Call up the configuration menu.
▶ Select a parameter with the / or . key and confirm with
the key.
The factory settings are highlighted in bold in the following
table.
Parameters Description
Tn (n=1,2,
...)
Check the temperature at the indoor unit.
CF Check the status of the fan.
SP Set the statistic pressure for the channel wall
unit.
• SP1: low
• SP2: middle 1
• SP3: middle 2
• SP4: high
AF Function test for three to six minutes.
tF Offset temperature for the Follow me
function.
• −5...0...5 °C
tyPE Restrict the control to specific operating
modes:
•CH: do not restrict available operating
modes.
• CC: no heating and automatic mode
• HH: only heating and Fan Mode
• NA: no automatic mode
tHI Maximum value of adjustable temperature
• 25...30 °C
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch CRC R-1 Climate Room Control at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch CRC R-1 Climate Room Control in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 4.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info