809317
10
Zoom out
Zoom in
Previous page
1/44
Next page
Installation
Compress 3400i AWS – 6721852066 (2023/01)
10
temperature. Comfort can also be adversely affected by using the
incorrect sensors.
Make sure that you use the correct sensor with the appropriate
characteristics when exchanging a sensor (Chapter 11.6). Using
sensors with other characteristics will lead to problems because the
system will be controlled with reference to the incorrect temperature.
5.1 Transport and storage
The indoor unit must always be transported and stored in an upright
position. If needed, it may be leaned temporarily.
The indoor unit may not be stored or transported at temperatures below
– 10 °C.
5.2 Insulation
NOTICE
Material damage from frost!
In case of a power failure, the water in the pipes may freeze.
All heat-conducting pipework must be provided with suitable thermal
insulation according to applicable regulations.
If it is envisaged that the cooling operation will be carried out below the
dew point, all connections and pipes must be appropriately insulated in
accordance with the valid regulations (minimum insulation thickness 13
mm).
5.3 Checklist
Each installation is different. The following checklist contains a general
description of the recommended installation steps.
As a recommendation, the refrigerant line should be connected before
the hydraulic connections.
The particle filter is installed horizontally in the heating system return
upstream of the inlet of the indoor unit. Note the direction of flow of the
filter.
1. Remove the front cover of the indoor unit.
2. Assemble the drip tray.
3. Mount the leakage copper pipe and assure the proper pipework from
the indoor unit.
4. Connect the refrigerant pipes from the outdoor unit to the indoor
unit.
5. Connect the indoor unit to the heating system.
6. Connect, fill and vent the DHW cylinder (if installed).
7. Before starting operation, fill the heating system.
8. Vent the heating system.
9. Install the outside temperature sensor and, if necessary, the room
controller.
10.Connect the CAN-BUS cable to the outdoor and indoor unit.
11.Install accessories (heating circuit module, etc.).
12.If required, connect the EMS BUS cable to the accessory.
13.Establish the electrical connection of the system.
14.Put the heating system into operation. Use the control unit to make
the necessary settings ( instructions for control unit).
15.Check that all sensors display the appropriate values.
16.Check and clean the particle filter.
17.Check the operation of the heating system after starting up (
instructions for control unit).
5.4 Removing the front cover of the indoor unit
Fig. 6 Remove front cover
To remove the front cover of the indoor unit, follow these steps:
1. Unscrew the lower part of the front cover.
2. Hold the lower part of the front cover on the holders.
3. Unscrew the upper part of the front cover.
4. Remove the upper part of the front cover.
5. Remove the intermediate connector of the control device and
complete the removal of the lower part of the front cover.
4
11
5
33
0010035653-002
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Compress 3400i AWS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Compress 3400i AWS in the language / languages: English as an attachment in your email.

The manual is 7.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch Compress 3400i AWS

Bosch Compress 3400i AWS User Manual - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info