Manual Bosch Compress 3000 - HP 200-1 E AI-F (page 16 of 40) (English)

697410

Zoom out

Zoom in

1/40

6 720 646 804

Installation instructions

3.7 Insulation blanket

If an insulation blanket is installed, the manufacturer’s

instructions included with the kit must be carefully fol-

lowed.

Application of any external insulation, blankets or water

pipe insulation to this water heater will require careful

attention to the following:

• Do not cover the temperature and pressure-relief

valve.

• Do not cover access panels to the heating elements.

• Do not cover the electrical junction box of the water

heater.

• Do not cover the operating or warning labels

attached to the water heater or attempt to relocate

them on the exterior of the insulation blanket.

• Do not block the air inlet grill or the exhaust vent

opening.

3.8 Filling the water heater

B Turn off power supply.

B Make certain the drain valve is completely closed.

B Open the shut-off valve in the cold water supply line.

B Open a hot water faucet to purge air from the water

heater and piping.

B A steady flow of water from the hot water faucet(s)

indicates a full water heater.

B Turn on power supply.

3.8.1 Water quality

If your water quality exceeds the levels in the table

below, you should consider treating or conditioning the

water entering the water heater. Bosch's warranty does

not cover product failures resulting from water quality

related issues.

3.9 Installation checklist

1. Tank location

• Is room size less than 10’ x 10’ x 7’ (700 cu. ft.)? If

yes, louvered door or similar ventilation is needed.

• Is there 5-½” of clearance (air space) between any

object and the front and rear shrouds?

• Is front of unit free and clear?

• Use level to confirm water heater is exactly vertical. If

not condensate will not drain properly. Add shims as

needed under the base of the unit.

• Are bracing straps (if required) in place?.

2. Plumbing connections

• Plumbing line must not block air filter removal on top

of the unit.

• Check for leaks on plumbing lines and water heater

connections.

3. Condensate lines are in place

• Connect both drain lines. Connect longer conden-

sate tube to lower drain and run to an appropriate

drain or condensate pump.

4. Ensure that the Temperature and Pressure-

Relief Valve is operational and the drain line is

installed per local code.

5. Electrical connections

• Electrical connections do not prevent air filter

removal.

• Confirm that water heater electrical circuit is properly

isolated.

6. Verify control panel displays 120°F Auto mode.

7. Front cover is in place.

Warning: The tank must be full of

water before heater is turned on. The

water heater warranty does not cover

damage or failure resulting from

operation with an empty or partially

empty tank.

Contaminant Recommended Level

Total Hardness

More than 2 gpg

Aluminum Up to 0.2 mg/L

Chlorides Up to 250 mg/L

Copper Up to 1.0 mg/L

Fluoride Up to 2.0 mg/L

Table 2 Source: Part 143 National Secondary Drink-

ing Water Regulations

Iron Up to 0.3 mg/L

Manganese Up to 0..05 mg/L

pH 6.5 to 8.5

Silver Up to 0.10 mg/L

Sulfate Up to 250 mg/L

TDS (Total Dissolved Solids) Up to 250 mg/L

Zinc Up to 250 mg/L

1) Hardness is not regulated by the National Secondary

Drinking Water Regulations

Contaminant Recommended Level

Table 2 Source: Part 143 National Secondary Drink-

ing Water Regulations

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Compress 3000 - HP 200-1 E AI-F in the language / languages: English as an attachment in your email.

The manual is 1,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch Compress 3000 - HP 200-1 E AI-F Manual

Product: