544277
27
Zoom out
Zoom in
Previous page
1/351
Next page
English | 27
Bosch Power Tools 1 609 92A 0D9 | (24.3.14)
Working with Wall Mount/Alignment Unit (Accessory)
(see figure B)
You can also mount the measuring tool to the wall mount with
alignment unit 39. For this, screw the 5/8" screw 42 of the
wall mount into the tripod mount 18 of the measuring tool.
Mounting to a wall: Mounting to a wall is recommended, e.g.,
for work above the elevation height of tripods or for work on
unstable surfaces and without tripod. For this, fasten the wall
mount 39, with the measuring tool mounted, as vertical as
possible to a wall.
For mounting to the wall, you can either fasten the wall mount
39 with fastening screw 40 to a lath (width maximal 8 mm) or
hang it up with two hooks.
Mounting on a tripod: The wall mount 39 can also be screwed
onto a tripod with the tripod mount on the back side. This
method of fastening is especially recommended for work
where the rotational plane is to be aligned with a reference
line.
With the alignment unit, the mounted measuring tool can be
moved vertically (when mounted to the wall) or horizontally
(when mounted to a tripod) within a range of approx. 16 cm.
For this, loosen screw 41 on the alignment unit, move the
measuring tool to the desired position, and retighten screw
41 again.
Working with the Ceiling Measurement Plate
(see figure B)
As an example, the ceiling measurement plate 44 can be used
for easy height adjustment of drop ceilings. Fasten the ceiling
measurement plate with the magnetic holder, e.g., to a beam.
The reflecting half of the ceiling measurement plate improves
the visibility of the laser beam in unfavourable conditions; the
laser beam can also be seen from the rear side through the
transparent half.
Working with the Laser Target Plate (Accessory)
(see figure C)
With the laser target plate 43, the laser mark can be projected
on the ground/floor or against a wall. With the magnetic hold-
er, the laser target plate can also be fastened to ceiling con-
structions.
With the zero field and the scale, the offset or drop to the re-
quired height can be measured and projected at another loca-
tion. This eliminates the necessity of precisely adjusting the
measuring tool to the height to be projected.
The laser target plate 43 has a reflecting coating which im-
proves the visibility of the laser beam from a larger distance or
in case of strong sun rays. The luminosity can be recognized
only if you look to the laser target plate in parallel to the laser
beam.
Working with the Measuring Rod (Accessory)
(see figure J)
For checking irregularities or projecting gradients, it is recom-
mended to use the measuring rod 36 together with the laser
receiver.
A relative millimetre scale (±50 cm) is marked on the top of
the measuring rod 36. Its zero height can be preset at the bot-
tom of the elevator column. This allows for direct reading of
deviations from the specified height.
Work Examples
Projecting/Checking Heights (see figure C)
Position the measuring tool in the horizontal position onto
a firm support or mount it onto a tripod 37 (accessory).
Working with tripod: Align the laser beam to the requested
height. Project or check the height at the target location.
Working without tripod: Determine the height difference
between the laser beam and the height at the reference
point with the laser target plate 43. Project or check the
measured height difference at the target location.
Parallel Alignment of a Plumb Beam/Projecting Right An-
gles (see figure D)
When right angles are to be projected or when partitions are
to be aligned, the plumb beam 9 must be aligned parallel,
meaning at the same distance to a reference line (e.g. a wall).
For this, set up the measuring tool in the vertical position
and position it in such a manner that the plumb beam runs
approximately parallel to the reference line.
For exact positioning, measure the clearance between
plumb beam and reference line directly on the measuring
tool with help of the laser target plate 43. Measure the
clearance between plumb beam and reference line again
as far away as possible from the measuring tool. Align the
plumb beam in such a manner that it has the same clear-
ance to the reference line as when measured directly at the
measuring tool.
The right angle to the plumb beam 9 is indicated by the varia-
ble laser beam 6.
Indicating a Plumb Line/Vertical Plane (see figure E)
To indicate a plumb line or a vertical plane, set up the measur-
ing tool in the vertical position. When the vertical plane is sup-
posed to run at a right angle to a reference line (e.g. a wall),
then align the plumb beam 9 with this reference line.
The plumb line is indicated by the variable laser beam 6.
OBJ_BUCH-757-008.book Page 27 Monday, March 24, 2014 11:19 AM
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch CHNM1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch CHNM1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 22,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info