780138
10
Zoom out
Zoom in
Previous page
1/51
Next page
English – 2
Technical data
Charger 4A Charger
Product code BPC3400
Rated voltage V~ 198to264
Frequency Hz 47to63
Battery charging voltage V= 36
Charging current (max.) A 4
Charging time for PowerTube 750,
approx. h 6
Operating temperature °C 0to40
Storage temperature °C 10to40
Weight, approx. kg 0.7
Protection rating IP40
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Operation
Start-up
Connecting the charger to the mains (see figure A)
uPay attention to the mains voltage. The voltage of the
power source must match the voltage specified on the
rating plate of the charger. Chargers marked 230 V can
also be operated at 220 V.
Plug the device connector (3) of the power cable into the
device socket (2) on the charger.
Connect the power cable (country-specific) to the mains.
Charging the removed battery (see figure B)
Switch the battery off and remove it from its holder on the
eBike. When doing so, read and observe the operating in-
structions of the battery.
uEnsure the battery is placed on clean surfaces only.
Avoid getting dirt, e.g. sand or soil, in the charging socket
and contacts in particular.
Plug the charging connector (5) of the charger into the
socket (6) on the battery.
Charging the battery on the bike (see figure C)
Switch the battery off. Clean the cover of the charging
socket (7). Avoid getting dirt, e.g. sand or soil, in the char-
ging socket and contacts in particular. Lift the cover of the
charging socket (7) and plug the charging connector (5) into
the charging socket (6).
uThere is a risk of fire due to the charger heating up
during charging. Ensure the battery on the bike is
completely dry and placed on a fireproof surface be-
fore charging. If this is not possible, remove the battery
from the holder and charge it in a more suitable location.
When doing so, read and observe the operating instruc-
tions of the battery.
Charging process
The charging process begins as soon as the charger is con-
nected to the battery or charging socket on the bike and to
the mains.
Note: The charging process is only possible when the tem-
perature of the eBike battery is within the permitted char-
ging temperature range.
Note: The drive unit is deactivated during the charging pro-
cess.
The battery can be charged with and without the on-board
computer. When charging without the on-board computer,
the charging procedure can be observed on the battery
charge indicator.
When the on-board computer is connected, a charging noti-
fication appears on the display.
The state of charge is displayed by the battery charge indic-
ator(8) on the battery and by the bars on the on-board com-
puter.
The LEDs on the battery charge indicator(8) flash during the
charging process. Each solid illuminated LED represents ap-
proximately 20% of the charging capacity. The flashing LED
indicates the next 20% currently charging.
Once the eBike battery is fully charged, the LEDs go out im-
mediately and the on-board computer is switched off. The
charging process is terminated. The state of charge can be
displayed for5 seconds by pressing the on/off button(9) on
the eBike battery.
Disconnect the charger from the mains and the battery from
the charger.
When the battery is disconnected from the charger, the bat-
tery is automatically switched off.
Note: If you have charged the battery on the bike, carefully
close the charging socket (6) with the cover (7) after char-
ging, so that no dirt or water can get in.
If the charger is not disconnected from the battery after
charging, after a few hours the charger will switch itself back
on, check the state of charge of the battery and begin the
charging procedure again if necessary.
0 275 007 3CX | (09.06.2021) Bosch eBike Systems
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch BPC3400 Charger - 2022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch BPC3400 Charger - 2022 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info