746696
17
Zoom out
Zoom in
Previous page
1/24
Next page
en Trouble shooting
16
3Trouble shooting
Tr oubl e shoot i ng
If a fault occurs, there is often a simple explanation.
Before calling the after-sales service, please refer to the
fault table and attempt to correct the fault yourself.
Tip: If a dish does not turn out exactly as you wanted,
refer to the following chapter, where you will find lots of
tips and notes relating to the optimum
settings.~ "Tested for you in our cooking studio"
on page 18
:Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Fault table
--------
Fault Possible cause Remedy/information
The appliance is not working The plug is not plugged into the mains Connect the appliance to the electricity supply
Power failure Check whether other kitchen appliances are working
The circuit breaker/fuse is faulty Check in the fuse box to make sure that the circuit
breaker/fuse for the appliance is in working order
Faulty operation Switch off the circuit breaker/fuse for the appliance in
the fuse box and switch it back on after approximately
10 seconds
Three zeros are lit on the display. Power failure Reset the time.
The appliance is not operating. A
cooking time is shown on the display.
The rotary selector has been accidentally turned. Press the "stop" button.
The "start" button has not been pressed after the set-
ting was applied.
Press the "start" button or cancel the setting by press-
ing the "stop" button.
The microwave is not working. The door has not been properly closed. Check whether food remnants or debris is/are
trapped in the door.
The "start" button has not been pressed. Press the "start" button.
It is taking longer than usual for food
to heat up
The microwave power output has been set too low. Select a higher microwave power setting.
A larger amount of food than usual has been placed in
the appliance.
Double the amount – double the time.
The food was colder than usual. Stir or turn the food during heating.
The turntable is making a scraping or
grinding noise.
Dirt or debris in the area around the turntable drive. Clean the roller ring and the recess in the cooking
compartment.
The microwave has stopped for no
apparent reason.
The microwave has a fault. If this fault recurs, please call the after-sales service.
An
i is shown on the display.
The appliance is in demo mode Deactivate demo mode.
~ "Basic settings" on page 14
Error message "E - 3" Fault in automatic door opening system. If an error message is displayed, switch the appliance
off and on again; if the message disappears, it was a
one-off problem. If the fault occurs again or the error
message is still displayed, please contact the after-
sales service and provide the fault code.
Customer service en
17
4Customer service
Cus t omer ser vi ce
Our after-sales service is there for you if your appliance
needs to be repaired. We will always find an
appropriate solution, also in order to avoid after-sales
personnel having to make unnecessary visits.
E number and FD number
When calling us, please quote the full product number
(E no.) and the production number (FD no.) so that we
can provide you with the correct advice. The rating plate
bearing these numbers can be found on the right-hand
side when you open the cooking compartment door.
To save time, you can make a note of the numbers for
your appliance and the telephone number of the after-
sales service in the space below in case you need
them.
Please note that a visit from an after-sales service
engineer is not free of charge in the event that the
appliance has been misused, even during the warranty
period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
Rely on the professionalism of the manufacturer. You
can therefore be sure that the repair is carried out by
trained service technicians who carry original spare
parts for your appliances.
This appliance corresponds to the standards EN 55011
and CISPR 11. It is a Group 2, Class B product.
Group 2 means that microwaves are produced for the
purpose of heating food. Class B states that the
appliance is suitable for private households.
Technical specifications
E no.
FD no.
After-sales service O
GB 0344 892 8979
Calls charged at local or mobile rate.
IE 01450 2655
0.03 € per minute at peak. Off peak 0.0088
per minute.
=1U)'(1U
7\SH
Input voltage 230-240 V AC, 50 Hz
Power consumption 1270 W
Max. output power 800 W (IEC 60705)
Max. grill output power 1000 W
Microwave frequency 2450 MHz
Circuit breaker/fuse rating 10 A
Dimensions (H/W/D)
- Appliance 382 x 594 x 317 mm
- Cooking compartment 201 x 308 x 282 mm
VDE approved Yes
CE mark Yes
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch BEL523MS0B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch BEL523MS0B in the language / languages: English as an attachment in your email.

The manual is 1,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info