591560
14
Zoom out
Zoom in
Previous page
1/205
Next page
14 | English
F 016 L81 148 | (22.10.14) Bosch Power Tools
Mounting and Operation
Working Advice
Starting
To start your Shredder, rotate the On/Off switch from posi-
tion “0” to position “II”. Allow machine to start and release
switch, which will return to position “I” (the normal run posi-
tion).
Note: The machine will not start if the On/Off switch is pushed
in slightly, whilst being rotated.
As a safety feature the machine will not start unless the hop-
per securing knob is fully tightened.
Restarting Protection
A mains failure causes machine to switch off. The machine
cannot restart on its own when the power returns.
Overload Protection
Overloading (e. g. blocking up of the cutter) can lead to a
standstill of the machine after a few seconds. After a short pe-
riod, the machine can be switched on again. If the machine
blocks again turn it off.
Remove blockage and restart.
Advice on Shredding
Branches become harder to shred depending on the type, age
and dryness of the wood.
For best results, shred fresh branches soon after they have
been cut.
Soft garden waste should be shredded in smaller loads, par-
ticularly when wet. Any blockages can be avoided by intermit-
tently shredding branches.
Blade Maintenance
Stop and remove plug from the power supply.
The blade has a double sided cutting edge.
When the cutting edges become blunt, the blade can be
turned over. The blade bolt may only be reused once, do not
reuse or use a non approved blade bolt. When both sides are
blunt replace the blade.
When fitting a new blade, discard old bolt and only use a
Bosch approved bolt, supplied.
Troubleshooting
The following chart lists problem symptoms, possible causes and corrective action, if your garden product does not operate
properly. If these do not identify and correct the problem, contact your service agent.
Warning! Switch off, remove plug from mains before adjusting, cleaning or if cable is cut, damaged or entangled.
Action Figure Page
Delivery Scope
1 201
Mounting wheels and undercarriage
2 201
Mounting the collecting bag and base
unit bearn
3 202
Connecting the Extension Lead
4 202
Starting
5 203
Working Advice
6 203
Stopping
7 204
Blade Maintenance
8 204
Maintenance, Cleaning and Storage
9 205
Selecting Accessories
10 205
Problem Possible Cause Corrective Action
Machine fails to operate Switch fails to operate Do not push On/Off switch while it is being rotated
Securing knob has not been fully tightened Tighten securing knob
Power turned off Turn power on
Mains socket faulty Use another socket
Extension cable damaged Inspect cable, replace if damaged
Fuse faulty/blown Replacse/restart
Motor protector has activated Follow “Overload Protection” procedure
Power supply interrupted Follow “Overload Protection” procedure
On/Off switch returns to position “0” Allow machine to cool then follow “Overload Protec-
tion” procedure
Machine functions
intermittently
Extension cable damaged Check mains cable and have it replaced, if required
Internal wiring of machine damaged Contact Service Agent
Motor protector has activated Follow “Overload Protection” procedure
On/Off switch returns to position “0” Allow machine to cool then follow “Overload Protec-
tion” procedure
OBJ_BUCH-2230-001.book Page 14 Wednesday, October 22, 2014 9:25 AM
14


Need help? Post your question in this forum.

Forumrules
1

Forum

bosch-axt-rapid-2000

Reset search

  • Stopped working, changed the fuse but only a short whine then stops again. Please help thank you. Submitted on 12-8-2022 at 10:15

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AXT Rapid 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AXT Rapid 2000 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info