Manual Bosch AXT 22 D (page 19 of 258) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591611

Zoom out

Zoom in

1/258

English | 19

Bosch Power Tools F 016 L81 145 | (28.8.14)

Assembly

For Your Safety

 Warning! Switch off, remove plug from mains before

adjusting, cleaning or if cable is cut, damaged or entan-

gled.

Observe correct mains voltage: The voltage of the power

source must agree with the voltage specified on the name-

plate of the unit. Equipment marked with 230 V can also be

connected to 220 V or 240 V.

The circuit must at least be protected as follows:

AXT 22 D/25 D/23 TC/25 TC/2550 TC= 13 A

An extension cable with a cross section that is too small caus-

es a distinct reduction in the performance capabilities of the

machine. For cables to 25 m in length, a cross section of at

least 3 x 1.5 mm

is required, for cables more than 25 m in

length, the cross section must be at least 2.5 mm

 WARNING! Inadequate extension cables can be dan-

gerous. Extension cable, plug and socket must be of

watertight construction and intended for outdoor use.

Cable connections should be kept dry and off the ground.

It is recommended for increased electrical safety to use a Residu-

al Current Device (RCD) with a tripping current of not more than

30 mA. Always check your RCD every time you use it.

If the supply cord is damaged, it must be replaced by a Bosch

Service Centre.

When using cable drums, these must be completely unreeled.

Products sold in GB only: Your product is fitted with a

BS 1363/A approved electric plug with internal fuse (ASTA

approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place by an author-

ised customer service agent. The replacement plug should

have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible

shock hazard and should never be inserted into a mains sock-

et elsewhere.

Assembly

Remove the machine from the package. (see figuresA–D).

Assemble the chute (seefigures E–F)

Operation

Starting Operation (see figure G)

 Always place the machine on firm level ground. During

operation, do not tilt or move.

 The motor will coast after switching off!

Remove earth from roots. Foreign material such as stones,

glass, metals, fabrics or plastics must not enter the chute as-

sembly 8. Otherwise this could damage the cutting roller 16.

The chute assembly 8 must be empty.

Starting

Press green button 4.

Stopping

Press red STOP button 5.

Wait for 2 seconds before restarting the machine.

Restarting Protection

A mains failure causes machine to switch off. The machine

cannot restart on its own when the power returns.

Return Motion

Press and hold the yellow button 6 to reverse the feed.

The cutting roller 16 runs backward and frees jammed mate-

rial.

Overload Protection

Overloading (e. g. blocking of the cutting roller 16) causes the

machine to stop after a few seconds, that time a beep is audible.

Press red STOP button to clear the error. After blocking the

tool can start in reverse direction.

Press and hold the yellow button 6 to reverse the cutter to un-

block.

In case of starting in the same direction the tool won’t start

and beeps.

If the blockage cannot be cleared the pressure plate 15 will

need to be moved away from the cutter.

The adjustment knob 10 will need to be turned a counter-

clockwise direction a small amount until the “jammed” mate-

rial is clear. The pressure plate 15 will need adjustment (see

“Pressure Plate Adjustment (see figure H)”).

Working Advice

 Wear eye protection, hearing protection and safety

gloves at all times while operating the machine.

 Always check before use that the collection box and

chute assembly are fitted correctly.

The machine is fitted with sensors, unless the collection box

11 is fitted correctly and the chute assembly 8 is correctly po-

sitioned, the machine will not start and the buzzer beeps (on

AXT 23 TC/ 25 TC 2550 TC also the 2 LEDs 14 flash).

Press the red STOP button to clear the error.

Insert the material to be shredded. The material will be fed by

the cutter roller 16 without further assistance.

 Lift back blade cover plate 13.

 Hook in chute assembly 8 to the garden product, and

then release the blade cover plate 13.

 Press the chute 8 down and turn red clamping knob 9

fully clockwise to lock the chute 8 in place, approxi-

mately 5x full turns of the clamping knob 9 are re-

quired.

OBJ_BUCH-895-004.book Page 19 Thursday, August 28, 2014 9:05 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AXT 22 D in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AXT 22 D Manual

Product: