Manual Bosch ART 26 COMBITRIM (page 17 of 194) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

537959

Zoom out

Zoom in

1/194

English - 3

Electrical Safety

Your machine is double insulated for safety and re-

quires no earth connection. The operating voltage is

230 V AC, 50 Hz (for non-EU countries 220 V,

240 V as applicable). Only use approved extension

cables. Contact your Bosch Service Center for de-

tails.

It is recommended for increased electrical safety to

use a Residual Current Device (RCD) with a tripping

current of not more than 30 mA. Always check your

RCD every time you use it.

WARNING: For safety, it is essential that the mains

plug 15 attached to the machine is fitted to the power

supply cable 17.

The couplings of connection leads must be pro-

tected against splashes and the coupling sockets on

the leads must be made of rubber or coated with rub-

ber.

Fixing means for the connection leads must be used.

The connection lead must be inspected for signs of

damage at regular intervals and may only be used if

in perfect condition.

If the supply cord is damaged, it must be replaced by

a Bosch Service Centre.

Extension cords/leads should only be used if they

comply with H05VV-F or H05RN-F types.

Products sold in GB only: Your machine is fitted with

an approved 13 A (BS 1363/A) electric plug and is

protected by a 13 A fuse (ASTA Approved to

BS 1362).

If the fitted plug is not suitable for your socket out-

lets, it should be cut off and an appropriate plug fitted

in its place by an authorized customer service agent.

The severed plug must be disposed of to avoid a

possible shock hazard and should never be inserted

into a 13 A socket elsewhere.

Do not connect the machine to the mains

socket before it is completely assembled.

Mounting the Cutting Guard

Place the cutting guard 10 on the trimmer head 7.

➊ Hook the guard onto trimmer head and push until

secure fitting.

➋ Push rear of guard until secure (click).

Mounting the Wheels

(ART 30/3000 COMBITRIM only)

Fit the wheels 11 onto the shaft 6.

Fit the bolt 19 and the wingnut 18.

Note: The position of the wheels can be adjusted by

loosening the wingnut 18 and moving to the desired

position.

The wheels can be moved up and down the

shaft 6 depending on the height of cut required.

Using Adjustable Handle

The adjustable handle 4 can be set in various posi-

tions:

➊ To change the position undo the handle wing

nut 3 and move the adjustable handle 4.

➋ Tighten the handle wing nut 3 securely to fix the

adjustable handle 4 in the adjusted position.

Adjusting Product Length

➊ Loosen the adjustment collar 5 90°.

➋ Pull the shaft out to increase the height, or push

the shaft in to decrease the height. Re-tighten ad-

justment collar 5.

Adjusting cutting head angle:

To change the angle depress the foot pedal 12 and

move the shaft 6 to the desired position.

Release the foot pedal 12.

Adjusting for Edging Mode

Moving wheels (where fitted):

➊ Loosen wingnut 18.

➋ Twist wheels 11 90° as shown.

➌ Tighten wingnut 18.

Adjusting cutting head angle:

➊ Depress the foot pedal 12.

➋ Move the shaft 6 to the lowest position. Release

the foot pedal 12.

Move trimmer head:

➊ Loosen the adjustment collar 5.

➋ Turn the shaft 6 90° to position the trimmer

head 7 for trimming/edging as shown. Re-tighten

adjustment collar 5.

For Your Safety

Warning! Switch off, remove plug from mains

before adjusting, cleaning or if cable is cut,

damaged or entangled.

The cutting line continues to rotate for a few

seconds after the trimmer is switched off.

Caution – do not touch rotating cutting line.

Assembly

Adjustment

F 016 L70 621.book Seite 3 Montag, 30. November 2009 3:03 15

17 • F 016 L70 621 • 09.11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch ART 26 COMBITRIM in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch ART 26 COMBITRIM Manual

Product: