Manual Bosch ART 23 GSA (page 15 of 97) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

537972

Zoom out

Zoom in

1/97

EURO • Printed in England • BA F 016 L69 858 • ART 23/25 • GB • OSW 07/01

English - 3

Electrical Safety

Your machine is double insulated for safety and re-

quires no earth connection. The operating voltage is

230 V AC, 50 Hz. Only use approved extension ca-

bles. Contact your service agent for details.

It is recommended for increased electrical safety to

use a Residual Current Device (RCD) with a tripping

current of not more than 30 mA. Always check your

RCD every time you use it.

WARNING: For safety, it is essential that the

mains plug 11 attached to the machine is fitted

to the power supply cable 13.

The couplings of connection leads must be protected

against splashes and the coupling sockets on the

leads must be made of rubber or coated with rubber.

Fixing means for the connection leads must be used.

The connection lead must be inspected for signs of

damage at regular intervals and may only be used if

in perfect condition.

If the supply cord is damaged, it must be replaced by

a Bosch approved Service Agent.

Extension cords/leads should only be used if they

comply with H05VV-F or H05RN-F types.

Products sold in GB only: Your mower is fitted with

an approved 13 A (BS 1363/A) electric plug and is

protected by a 13 A fuse (ASTA Approved to

BS 1362).

If the fitted plug is not suitable for your socket outlets,

it should be cut off and an appropriate plug fitted in

its place.

The severed plug must be disposed of to avoid a

possible shock hazard and should never be inserted

into a 13 A socket elsewhere.

Do not connect the machine to the mains

socket before it is completely assembled.

Mounting the Cutting Guard

Place the cutting guard 8 on the trimmer head 6.

First locate rear clip onto trimmer head and push

until secure fitting (click 1). Repeat fitting for

front clip (click 2).

Using Adjustable Handle

(Model ART 23 GFS/GFSV)

(Model ART 25 GSA/GSAV)

The adjustable handle 4 can be set in various

positions, see figure B:

➊

To change the position unfold the clamping le-

ver 10 and turn the adjustable handle 4:

I = Park position for space saving storage.

II = Handle forward for horizontal trimming with op-

timum balance and control see figure E3.

III = Handle back for one-handed trimming, une-

qualled trimming range, and support see fig-

ure E2.

IV = Handle location for vertical trimming and edg-

ing jobs.

➋

Fold the clamping lever 10 back to fix the adjust-

able handle 4 in the adjusted position.

Adjusting Handle Height or

Trimming/Edging Position

(Model ART 23 GFSV)

(Model ART 25 GSAV)

(Model ART 25 ERGOPOWER)

➊

Push down release button 9.

➋

Adjust the shaft 5 to one of six possible handle

height positions.

➌

If necessary turn the shaft 5 180° to position

the trimmer head for trimming/edging as

shown.

Remove stones, loose pieces of wood and

other objects from the cutting area.

The cutting line continues to rotate for a few sec-

onds after the trimmer is switched off. Allow the

motor/cutting line to stop rotating before switch-

ing “on” again.

Do not rapidly switch off and on.

Switching On and Off

Press switch 1 and hold depressed. Release

switch 1 for switching off.

Cutting Grass

Move the trimmer left and right, keeping it well

away from the body.

The trimmer can efficiently cut grass up to a height of

15 cm. Cut taller grass in stages.

For Your Safety

Warning! Switch off, remove plug from mains

before adjusting, cleaning or if cable is cut,

damaged or entangled.

The cutting line continues to rotate for a few

seconds after the trimmer is switched off.

Caution - do not touch rotating cutting line.

Assembly

Adjustment

Cutting and Edging

F016 L69 858.book Seite 3 Freitag, 6. Juli 2001 11:50 11

15 • F016 L69 858 • 07.01

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch ART 23 GSA in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch ART 23 GSA Manual

Product: