Manual Bosch Aquatak Go (page 15 of 119) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

78575

Zoom out

Zoom in

1/119

English | 15

Bosch Power Tools F016 L70 529 | (7.2.08)

Safety Notes

Before start-up please read these in-

structions!

Before using the machine please read the op-

erating instructions for your unit and comply in

particular with these safety instructions.

The warning and information signs attached to

the unit provide important information for safe

operation.

Apart from the information in the operating in-

structions comply with the general safety reg-

ulations and regulations for the prevention of

accidents.

Never direct the water jet at peo-

ple, animals, the unit or electric

components.

Power supply

f The voltage indicated on the rating plate

must correspond to the voltage of the power

source.

f We recommend that this equipment is only

connected into a socket which is protected

by a circuit-breaker that would be actuated

by a 30 mA residual current.

f Only use or replace power supply cables for

this unit which correspond to the types indi-

cated by the manufacturer. See the operat-

ing instructions for the order no. and types.

f If the plug is damaged, pay attention to the

following:

f Plugs and sockets conforming to BS 4243 or

BS 196 should be used wherever practicable.

Domestic pattern plugs to BS 1363 are not

recommended but if their use is essential

those which have barriers or moulded chan-

nels inside should be selected so that if the

earth continuity conductor is pulled out of its

terminal it is unlikely to be able to touch the

phase terminal of the fuse carrier. Domestic

pattern plugs to BS 546 should not be used.

The wiring of the plug should leave more

slack in the earth continuity conductor than

in the other cores, so that it is not the first

core to be pulled out of its terminal should

the cord grip fail. Plugs which have good

grips capable of maintaining a firm hold on

the cable sheath should be selected. In gen-

eral, additional means should be provided to

relieve stress on cable terminations in the

plug. For example, additional cable clamps

should be fitted or a substantial chain could

be used to tether the machine to a fixed

point.

f Plugs and sockets situated near the work site

or outdoors should be to class IP 55 of

BS 5490 to provide adequate protection

against ingress of water, etc. and cable en-

tries require effective sealing. Rubber

shrouds should be provided over cable

glands. Drip-proof (class IP X2 of BS 5490)

plugs and sockets to BS 4343 are suitable for

use indoors where the plug is away from the

water spray area where the appliance is in

use.

f Never touch the mains plug with wet hands.

f Do not run over, crush or pull the power sup-

ply cable or extension lead, otherwise it may

be damaged. Protect the cable from heat, oil

and sharp edges.

f The extension lead must have a cross section

in accordance with the operating instruc-

tions and be protected against splashed wa-

ter. The connection must not be in water.

f When replacing couplings on the power sup-

ply cable or extension lead the spray water

guard and mechanical stability must remain

intact.

Water connection

f Comply with the regulations of your water

supply company.

f All connecting hoses must have properly

sealed joints.

f The high-pressure hose must not be dam-

aged (danger of bursting). A damaged high-

pressure hose must be replaced immediate-

ly. Only use hoses and connections recom-

mended by the manufacturer.

OBJ_BUCH-683-001.book Page 15 Thursday, February 7, 2008 4:29 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Aquatak Go in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch Aquatak Go

Bosch Aquatak Go User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 119 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch Aquatak Go Manual

Product: