Manual Bosch Aquatak 1500 (page 15 of 97) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

119949

Zoom out

Zoom in

1/97

English - 3

15 • F016 L70 374 • TMS • 28.09.05

Electrical Safety

Your machine requires an earth connection. The op-

erating voltage is 230 V AC, 50 Hz. (for non-EU

countries 220 V, 240 V as applicable). Only use ap-

proved extension cables. Contact your Bosch Serv-

ice Centre for details.

If you want to use an extension cable when operat-

ing your high pressure washer, only the following ca-

ble dimensions should be used:

1.5 mm

– max length 20 m

2.5 mm

– max length 50 m

Note: If an extension cable is used it must be

earthed and connected through the plug to the earth

cable of your supply network in accordance with pre-

scribed safety regulations.

If in doubt contact a qualified electrician or the near-

est Bosch Service Center.

WARNING! Inadequate extension cables can be

dangerous. Extension cable, plug and socket

must be of watertight construction and intended

for outdoor use.

Cable connections should be kept dry and off

ground.

It is recommended for increased electrical safety to

use a Residual Current Device (RCD) with a tripping

current of not more than 30 mA. Always check your

RCD every time you use it.

For products not sold in GB: WARNING: For

safety, it is essential that the mains plug attached to

the product is fitted to the power supply cable . The

couplings of connection leads must be protected

against splashes and the coupling sockets on the

leads must be made of rubber or coated with rubber.

Fixing means for the connection leads must be

used.

If the supply cord is damaged, it must be replaced by

a Bosch Service Centre.

Products sold in GB only: Your product is fitted with

an approved 13 A (BS 1363/A) electric plug and is

protected by a 13 A fuse (ASTA Approved to

BS 1362).

If the fitted plug is not suitable for your socket out-

lets, it should be cut off and an appropriate plug fit-

ted in its place.

The severed plug must be disposed of to avoid a

possible shock hazard and should never be inserted

into a 13 A socket elsewhere.

Water connection

/ / Fit cable winder 3, using screws pro-

vided (four on Aquatak 1350)

Fit handle 7 to hose drum 6. (AQUATAK 1500 X)

Screw inlet connector 9 onto machine water inlet

connection 14.

Connecting high pressure water supply hose/

nozzle

/ Securely screw high pressure hose 11 onto

machine at connection 15.

/ Securely screw the high pressure hose 11 to

the hose drum 6 and to the power gun 4.

(AQUATAK 1500 X)

Inserting the vario-jet/fan power lance 5 into the

power gun 4. Depress and turn the vario-jet/fan

power lance 90° clockwise to lock in place.

Attach water supply hose (not supplied) to the

mains water supply and machine.

Before use (Aquatak 1500 X only)

Unwind the pressure hose 11 off the hose

drum 6.

Never use the pressure washer with the high pres-

sure hose 11 on the hose drum 6.

Vario-jet-fan power lance

(Colour coded yellow – AQUATAK 1350/

Colour coded green – AQUATAK 1500 X)

Twist the front ring to adjust from a pencil to a fan

jet and vice versa.

To apply the detergent twist the rear ring as

shown from high pressure mode to low pressure

mode.

To adjust the spray pattern twist the front ring.

Roto power lance

(Colour coded yellow – AQUATAK 1350/

Colour coded orange – AQUATAK 1500 X)

Turn the vario-jet/fan power lance 5 90° anti-

clockwise. Extract the vario-jet/fan power lance.

Insert the roto-power lance 10 into the power

gun 4. Depress and turn the roto-power lance 90°

clockwise to lock in place.

For Your Safety

Warning! Switch off, remove plug from mains

before adjusting, cleaning or if cable is cut,

damaged or entangled.

Assembly

Adjustments and using different

nozzles

F016 L70 374 - GB Seite 3 Freitag, 21. Oktober 2005 9:57 09

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Aquatak 1500 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch Aquatak 1500 Manual

Product: