697454
48
Zoom out
Zoom in
Previous page
1/170
Next page
48 en | Settings AMAX panel
2019.08 | 11 | F.01U.309.277 Installation Manual Bosch Security Systems B.V.
RPC gets the Subscriber ID, IP address and port from the UDP data packets (IP No. and Port
is parsed from UDP data packet).
RPC with running RPS (Remote Programming Software = A-Link Plus) saves the received UDP
data packet information into its own RAM, the information is lost after RPS is closed.
When a connection is started and the IP address set in the customer information doesn’t
match with the IP Address from the RAM, the A-Link Plus opens a window to ask if the new IP
Address and Port should be used.
When RPS is opened, a connection can only be established when the IP address and port
number of the AMAX panel have not changed, after RPS received previous data.
If the IP address has changed RPC with running RPS must wait for the next UDP Data package
send from the Panel. When the connection is established, the AMAX panel sends a polling
telegram of 25 bytes.
6.1.8 Call back and domestic call
Call back telephone number
This address stores the telephone number to call when upload / download is requested or the
user enters his code + [5] [7] and presses [#] to initiate a modem call from the AMAX panel to
establish a communication link with the remote computer. The computer must be running
remote programming software A-Link Plus and must be set to waiting for an incoming call. The
call back telephone number is also necessary if remote connect with call back verification is
required.
Domestic call
Four recordable voice messages for four dialing telephone numbers are supported. Each of the
four recordable voice messages can take up to 9 seconds. The voice messages are recorded
with the tool “Rec.exe” that comes with A-Link Plus and are transferred via A-Link Plus to the
AMAX panel. They can only be transferred via USB or network connection. The supported
format of the voice message files is the following:
For firmware version up to 1.4: .wav
For firmware version 1.5 and higher: .va3
When the AMAX panel is activated into zone tamper / zone alarm, the programmed telephone
number is dialed and the recorded voice message is played.
All alarm events only need one report / acknowledgement.
The transmission sequence is repeated until the AMAX panel receives an acknowledgement
tone.
The AMAX panel automatically hangs up after about 45 seconds if it cannot detect the
acknowledgement tone and redial later.
The user presses any key on the telephone between two acknowledgement tones to confirm
the alarming.
The acknowledgement tone is the DTMF signal sent by the remote user with any key ([0] - [9]
or [*] or [#]).
If the AMAX panel received the acknowledgement from the user, it will send a 2 seconds long
confirmation beep as an acknowledge tone and hang up the line.
6.1.9 Ring times
Ring Count
This function defines the number of rings before the AMAX panel answers an incoming call. It
is necessary to enable remote arming and remote upload/download to use this function.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AMAX panel 4000 EN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AMAX panel 4000 EN in the language / languages: English as an attachment in your email.

The manual is 2,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch AMAX panel 4000 EN

Bosch AMAX panel 4000 EN Quick start guide - German - 76 pages

Bosch AMAX panel 4000 EN Quick start guide - Dutch - 76 pages

Bosch AMAX panel 4000 EN Installation Guide - Dutch - 190 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info