697454
38
Zoom out
Zoom in
Previous page
1/170
Next page
38 en | Settings AMAX panel
2019.08 | 11 | F.01U.309.277 Installation Manual Bosch Security Systems B.V.
6.1.2 Reports
System reporting
Report transmission sequence
If the event has disabled the report (option 0), no report is sent out. If the report has any
destination to contact the panel (option 1 - 11), It will call the related destination by related
reporting format type and subscriber ID number.
Attempt rules:
1. Attempt times and duration
Within the report expiring time the AMAX panel will retry sending the report to each
enabled destination till the report has been sent to the destination, or till the report
buffer overflows and the old report is replaced by new incoming reports.
For each enabled destination, the retry interval time between two retries is 15
seconds for the 1st retry to 4th retry, and the retry interval time between two retries
is 10 minutes for the 5th retry to 8th retry, after the 8th retry the retry interval time
between two retries is 60 minutes.
2. Attempt priority
The attempt priority is destination 1, 2, 3, 4 Domestic. The disabled destinations will
be ignored.
3. Communication fail fault
If the attempt times for one destination reaches 4, the system will cause the
communication fail fault for this destination.
4. Backup destination process
The AMAX panel can save up to a maximum of 50 un-reported events. If the un-
reported events are more than 50, it will delete earlier event and only save the last
50 events in the buffer to send out.
Sequential logic to send report
If the event reporting path is disabled, the relevant reports will not be sent.
If the event reporting path is set to a single path (receiver 1, 2, 3 or 4), the AMAX panel
will send a report to the corresponding path.
If the event reporting path is set to more than one path (e.g. receiver 1, 2, 3, 4) and any
of these paths fails, the reporting will fail.
If the event reporting path is set to one or more receivers with other receivers as backup,
the AMAX panel will send the report to the main receivers first. Only this reporting fails,
the AMAX panel attempts to send the report to the backup receivers in succession.
Communication path fault will occur when all valid paths fail. Communication path fault
will recover when any one of the paths recovers.
Display of faults
When multiple reports are queued for delivery, the communication path fault is displayed as a
logic or relationship. Example:
Set zone status recovery report to send report to receiver 1. Set keypad emergency report to
send report to receiver 1, with receiver 2, 3, and 4 as backup.
Communication path fault is as follows: When communication paths 1, 2, 3, and 4 all fail, only
the illumination of zone indicator 1 expresses that communication path 1 of the zone status
recovery report fails and the all communication paths 1, 2, 3 and 4 of the keypad emergency
report fail as well.
Communication path fault recovery is as follows:
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AMAX panel 4000 EN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AMAX panel 4000 EN in the language / languages: English as an attachment in your email.

The manual is 2,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch AMAX panel 4000 EN

Bosch AMAX panel 4000 EN Quick start guide - German - 76 pages

Bosch AMAX panel 4000 EN Quick start guide - Dutch - 76 pages

Bosch AMAX panel 4000 EN Installation Guide - Dutch - 190 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info