78524
22
Zoom out
Zoom in
Previous page
1/159
Next page
English - 5
22 • F016 L70 360 • TMS • 11.07.06
6. Check if all parts are seated properly and hold
chain and chain bar in a level position.
7. Fit cover plate, check that arrows are still aligned
and ensure that the chain catch bolt 22 fits into
the groove of the cover plate 15.
8. Screw on the cover plate 15 with the locking
knob 14.
The chain is not yet tensioned. Tensioning the chain
applies as described under “Tensioning chain”, item
1–7.
Tensioning chain
Always check the chain tension before use, after the
first cuts and regularly during use, approx. every
10 minutes. Upon initial operation, new chains can
lengthen considerably.
The chain life of the saw chain mainly depends upon
sufficient lubrication and correct tensioning.
Avoid tensioning the chain if it is hot, as this will
cause the chain to become overtensioned when it
cools down.
1. Place the chain saw on any suitable flat surface.
2. Turn locking knob 14 approx. 1 3 turns anti-
clockwise to loosen the chain bar.
3. Check if the chain links are correctly located in
the slot around the chain bar 11 and drive
sprocket 21.
4. Turn the red tensioning ring 13 clockwise ratchet-
ing until the correct chain tension is reached. The
ratchet mechanism prevents the chain tension
from loosening. The locking knob 14 may also
turn, when turning the tension ring 13. If the ten-
sioning ring 13 is hard to turn, loosen the locking
knob 14 once more anticlockwise.
5. The correct chain tension is reached when the
chain 10 can be raised approx. 3 4 mm from the
chain bar in the centre. This should be done by
using one hand to raise the chain against the
weight of the machine.
6. If the chain 10 is overtensioned, turn tensioning
ring 13 anticlockwise to loosen the chain.
7. If the chain 10 is tensioned optimal, lock the chain
bar 11 by tightening the locking knob 14 in clock-
wise direction. Do not use tools.
20
21
17
18
11
15 22
14
A
13
14
3-4 mm
10
14
F016 L70 360 - GB Seite 5 Dienstag, 18. Juli 2006 9:20 09
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AKE 40-18S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AKE 40-18S in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info