697426
10
Zoom out
Zoom in
Previous page
1/28
Next page
10 | Installing the solar pump station
AGS10-2, AGS10E-2, AGS20-2, AGS50-26 720 811 270 (2015/04)
5.3.1 Solar pump station with an external controller
You will find notes regarding the electrical connection in the controller
instructions.
5.4 Installing the safety assembly
Install the safety assembly on the solar pump station together with the
gasket supplied [1].
Fig. 14 Installing the safety assembly
[1] Gasket (21x30x2)
5.5 Connecting the expansion vessel and pre-cooling
vessel
5.5.1 Installing the pre-cooling vessel with evacuated tube
collectors (available as accessory)
With evacuated tube collectors, a pre-cooling vessel is required if:
The system is designed to support a central heating system.
The system is purely for DHW heating and the solar fraction is more
than 60 %.
The minimum pipe length or the minimum height distance cannot be
achieved ( Chapter 4.2, page 8).
The pre-cooling vessel protects the expansion vessel from excessively
high temperatures.
Connecting the pre-cooling vessel
If the pipeline to the expansion vessel needs to be laid on a rising incline,
an additional air vent must be installed.
Secure pipework to and from the pre-cooling vessel with pipe clips
[4]. Mount the pre-cooling vessel vertically.
Connect the expansion vessel [5] to the pre-cooling vessel by means
of a copper pipe.
Seal the connection on the pressure relief valve with a ¾ " cap [2] on
site.
Fig. 15 Installing the pre-cooling vessel
[1] Flexible stainless steel hose from the connection set for the
expansion vessel (available as accessory)
[2] Safety assembly (provided by installer)
[3] Pre-cooling vessel
[4] Pipe clip (on site)
[5] Expansion vessel
5.5.2 Installing the solar expansion vessel (available as an
accessory)
Install the expansion vessel with the mounting materials provided.
Never turn off the heating system when you are away on
holiday or in summer as this may disable the solar
system.
For a single-line solar pump station:
Install the safety assembly on the left.
Do not insulate the pre-cooling vessel (if fitted) and the
expansion vessel, nor the pipes connecting them to the
safety assembly.
6 litre 12 litre
Height 270 mm 270 mm
Diameter 160 mm 270 mm
Port 2 x R ¾ " 2 x R ¾ "
Maximum operating pressure 10 bar 10 bar
Table 6 Pre-cooling vessel specifications
1
7747006489.13-2.ST
WARNING: Risk of injury If the pressure relief valve is
damaged, this may result in an explosion.
To protect the pressure relief valve from excessive
temperatures:
Connect the pre-cooling and expansion vessels with a
tee (¾ " outer thread with flat gasket) in the return 20
to 30 cm above the solar pump station.
WARNING: Risk of injury If the pressure relief valve is
damaged, this may result in an explosion.
To protect the pressure relief valve from excessive
temperatures:
Connect the pre-cooling and expansion vessels with a
tee (¾ " outer thread with flat gasket) in the return 20
to 30 cm above the solar heating station.
20-30 cm20-30 cm
7747006489.14-2.ST
1
2
3
4
5
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AGS50-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AGS50-2 in the language / languages: English as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info