697423
14
Zoom out
Zoom in
Previous page
1/28
Next page
14 | Commissioning
AGS10-2, AGS10E-2, AGS20-2, AGS50-26 720 811 270 (2015/04)
6.2.3 Replacing water with heat transfer medium
You can use electric pumps, hand pumps or power drill attachments
capable of generating pressures of at least 2 bar for filling.
Using a pump, fill the solar system via one of the fill and drain valves
[1] in the solar pump station.
Fig. 23 Filling via DFV
Set the ball valves ( Fig. 22, [1]) on the thermometers to 45° and
open the flow limiter ( Fig. 22, [2]) and other shut-off devices.
Fill the solar system slowly so that air bubbles do not form.
Lastly, set the ball valves on the thermometers so that the gravity
brakes are ready for operation (0° position).
6.2.4 Verifying that the solar thermal system is free of air
Switch the solar pump(s) on and off manually.
While switching the pump on and off, observe the black pointer on the
pressure gauge [1] on the safety assembly.
Fig. 24 Checking the pressure gauge display
6.2.5 Determining the operating pressure
When putting the system into operation, the operating pressure must be
0.7 bar above the static pressure (1 metre difference in height equals
0.1 bar).
The system pressure must be at least 1.5 bar (when cold, 20 °C).
If there is not enough pressure, pump in more heat transfer medium.
Once ventilation is complete, close the ball valve [2] of the air vent
and the plug screw [1].
Fig. 25 Closing the air vent and ball valve
The pipes must be completely emptied of water,
otherwise the heat transfer medium can become diluted.
If the black pointer on the pressure gauge [1] indicates
pressure fluctuations when the solar pump is switched on
and off, there is still air in the solar thermal system which
must be removed.
7747006489.36-2.ST7747006489.36-2.ST
1
1
S E
7747006489.33-2.ST
1
Flat plate Evacuated tube
Static height
1)
1) A one metre difference in height (between collector array and solar pump station)
means 0.1 bar
(10 m) 1.0 bar (10 m) 1.0 bar
+ allowance + 0.7 bar + 2.0 bar
= operating pressure = 1.7 bar = 3.0 bar
Table 9 Example: collector-dependent operating pressure
When heat transfer medium evaporates in the collector,
pressure relief can only be achieved by the solar
expansion vessel if the air vent is closed.
6720801165.15-2.ST
2
1
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch AGS10-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AGS10-2 in the language / languages: English as an attachment in your email.

The manual is 2,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info