Manual Bosch AdvancedTableCut 52 (page 20 of 305) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian)

766874

Zoom out

Zoom in

1/305

20 | English

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

Service

uHave your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Safety information for table saws

Guarding related warnings

uKeep guards in place. Guards must be in working or-

der and be properly mounted. A guard that is loose,

damaged, or is not functioning correctly must be repaired

or replaced.

uAlways use saw blade guard and riving knife for every

through–cutting operation. For through-cutting opera-

tions where the saw blade cuts completely through the

thickness of the workpiece, the guard and other safety

devices help reduce the risk of injury.

uMake sure the saw blade is not contacting the guard,

riving knife or the workpiece before the switch is

turned on. Inadvertent contact of these items with the

saw blade could cause a hazardous condition.

Cutting procedures warnings

u DANGER: Never place your fingers or hands in the

vicinity or in line with the saw blade. A moment of inat-

tention or a slip could direct your hand towards the saw

blade and result in serious personal injury.

uFeed the workpiece into the saw blade or cutter only

against the direction of rotation. Feeding the work-

piece in the same direction that the saw blade is rotating

above the table may result in the workpiece, and your

hand, being pulled into the saw blade.

uNever use the mitre gauge to feed the workpiece

when ripping and do not use the rip fence as a length

stop when cross cutting with the mitre gauge. Guiding

the workpiece with the rip fence and the mitre gauge at

the same time increases the likelihood of saw blade bind-

ing and kickback.

uWhen ripping, always apply the workpiece feeding

force between the fence and the saw blade. Use a

push stick when the distance between the fence and

the saw blade is less than 150mm, and use a push

block when this distance is less than 50 mm. “Work

helping” devices will keep your hand at a safe distance

from the saw blade.

uUse only the push stick provided by the manufacturer

or constructed in accordance with the instructions.

This push stick provides sufficient distance of the hand

from the saw blade.

uNever use a damaged or cut push stick. A damaged

push stick may break causing your hand to slip into the

saw blade.

uDo not perform any operation “freehand”. Always use

either the rip fence or the mitre gauge to position and

guide the workpiece. “Freehand” means using your

hands to support or guide the workpiece, in lieu of a rip

fence or mitre gauge. Freehand sawing leads to misalign-

ment, binding and kickback.

uNever reach around or over a rotating saw blade.

Reaching for a workpiece may lead to accidental contact

with the moving saw blade.

uProvide auxiliary workpiece support to the rear and/

or sides of the saw table for long and/or wide work-

pieces to keep them level. A long and/or wide work-

piece has a tendency to pivot on the table’s edge, causing

loss of control, saw blade binding and kickback.

uFeed workpiece at an even pace. Do not bend or twist

the workpiece. If jamming occurs, turn the tool off im-

mediately, unplug the tool then clear the jam. Jam-

ming the saw blade by the workpiece can cause kickback

or stall the motor.

uDo not remove pieces of cut-off material while the saw

is running. The material may become trapped between

the fence or inside the saw blade guard and the saw blade

pulling your fingers into the saw blade. Turn the saw off

and wait until the saw blade stops before removing mater-

ial.

uUse an auxiliary fence in contact with the table top

when ripping workpieces less than 2 mm thick. A thin

workpiece may wedge under the rip fence and create a

kickback.

Kickback causes and related warnings

Kickback is a sudden reaction of the workpiece due to a

pinched, jammed saw blade or misaligned line of cut in the

workpiece with respect to the saw blade or when a part of

the workpiece binds between the saw blade and the rip

fence or other fixed object.

Most frequently during kickback, the workpiece is lifted from

the table by the rear portion of the saw blade and is pro-

pelled towards the operator.

Kickback is the result of saw misuse and/or incorrect operat-

ing procedures or conditions and can be avoided by taking

proper precautions as given below.

uNever stand directly in line with the saw blade. Always

position your body on the same side of the saw blade

as the fence. Kickback may propel the workpiece at high

velocity towards anyone standing in front and in line with

the saw blade.

uNever reach over or in back of the saw blade to pull or

to support the workpiece. Accidental contact with the

saw blade may occur or kickback may drag your fingers

into the saw blade.

uNever hold and press the workpiece that is being cut

off against the rotating saw blade. Pressing the work-

piece being cut off against the saw blade will create a

binding condition and kickback.

uAlign the fence to be parallel with the saw blade. A

misaligned fence will pinch the workpiece against the saw

blade and create kickback.

1 609 92A 66E | (12.01.2021) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch AdvancedTableCut 52 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 7,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch AdvancedTableCut 52 Manual

Product: